Manuals / Xantrex Technology / Computer Equipment / Tablet Accessory

Xantrex Technology IP1012 AL manual Physical Specifications, Physical specifications

Models: IP1012 AL

1 52

Download 52 pages 11.23 Kb

Page 38

Image 38

Specifications

Physical Specifications

Physical specifications

Enclosure	Sealed; dust and water-resistant; ignition
	protected

Dimensions	Approximately. 8.5" (21.8 cm) H x 7”
	(17.7 cm) W x 13.0"(33.0 cm) D, excluding DC
	ground connector (similar to Group 31 battery
	dimensions)

Net weight	40 lbs. (18 kg) maximum without mounting
	brackets or external cables

External finish	Base - Clear anodized aluminum.
	Top cover - black anodized or black powder
	coated aluminum

Mounting Orientation	All allowed

Mounting method	Four M8x1.25 threaded holes accessible from
	bottom only, one in each corner, and/or battery
	hold-down bar over center top of cover.
	Recommended torque: 5-6 ft-lb (7-8 Nm)

Battery cable	#2 AWG Minimum, maximum 10 feet long,
	each way

Battery size 12 volt	225 Ah minimum to prevent overstress of
	battery in charge mode; 400 Ah recommended

A–2	975-0337-01-01

Page 38

Image 38

Xantrex Technology IP1012 AL manual Physical Specifications, Physical specifications

Contents

IP1012 AL IP1012 AL Inverter/Charger with Ignition ProtectionOwner’s Guide Page Owner’s Guide IP1012 AL Inverter/ Charger with Ignition ProtectionNotice of Copyright About XantrexTrademarks Exclusion for DocumentationScope About This GuidePurpose AudienceConventions Used Related InformationImportant Safety Information General PrecautionsPrecautions When Working With Batteries Precautions for Using Rechargeable Devices1 Introduction Contents3 Maintenance 2 OperationTroubleshooting 4 TroubleshootingA Specifications 1 Introduction Inverter/charger Features Operating Features Charger features 2 Operation AC loads Planning for AC LoadsType of Loads DC loads Ambient TemperatureProblem loads Calculating Size of an AC Load Battery condition Factors affecting load Minutes ApplianceWatts HoursRunning the Alternator While Operating AC and DC Loads Indication Switch settings Figure 2-3 Remote switch with indicator lightsUsing the Remote Switch The switch shown in Figure 2-3 is used to disable the inverter. Theindicators lights SwitchThe switch indicator lights i.e., LED provide information about the the lights will behave like thisTurning the Inverter On and Running Loads Running in Extremes Of Hot or Cold TemperaturesOperating the Inverter/Charger Restarting After a ShutdownMiscellaneous Hints Battery ChargingUsing Shorepower disconnecting the IP1012 AL from the batteries 3 MaintenanceChapter 3, “Maintenance” provides procedures for removing or connecting the AC input and output cablesTo remove the terminal cap Maintaining the Inverter/chargerChecking Terminals Connecting Disconnecting and Connecting the BatteriesDisconnecting WARNING Explosion or Fire To disconnect from the batteryWARNING Correct Fuse Type Replacing the FuseWARNING Possible popping sound and sparks CAUTION Do not overtighten fuse nuts To replace the fuseTo reconnect Removing and Reconnecting AC CablesTo remove the AC cables 4 Troubleshooting Troubleshooting Common ProblemsSymptom Blinking Lights on the Remote SwitchTroubleshooting reference Continued Possible ProblemTable 4-2 Charger indicator blink patterns Table 4-3 Inverter indicator blink patternsA Specifications All specifications are subject to change without noticePhysical Specifications Physical specificationsInverter Specifications Charger Specifications Charger specificationsTransfer and general specifications Transfer and General SpecificationsCharger specifications Continued Figure A-1 Output surge rating Figure A-2 Charging current versus temperature derating curveRating Curves and Charging Profiles PowerFloat Charge Figure A-3 Three-stage charging profileBulk DC VoltagePage Index extension cord see connection cordPage Warranty and Return Information WarrantyDisclaimer ProductExclusions Return Material Authorization PolicyReturn Procedure Out of Warranty Service Information About Your SystemPage 1 800 994 7828 Fax toll free NA Xantrex Technology Inc1 800 670 0707 Tel toll free NA 1 360 925 5097 Tel direct 975-0337-01-01