Manuals / Xantrex Technology / Computer Equipment / Tablet Accessory

Xantrex Technology IP1012 AL manual Removing and Reconnecting AC Cables, To remove the AC cables

Models: IP1012 AL

1 52

Download 52 pages 11.23 Kb

Page 32

Image 32

Maintenance

Removing and Reconnecting AC Cables

To remove the AC cables:

➣Grasp the knurled surface of the connector housing as shown in Figure 3-3 and turn counter clockwise approximately one-half turn. Gently pull the cable out by grasping the connector.

To reconnect:

1.Align the key of the connector with the slot on the terminal of the IP1012 AL.

2.Insert the connector firmly. Turn the connector housing clockwise 1/2 turn until you feel resistance, then another 1/8 turn until it locks into place.

Inverter/charger control cable

AC output connector

AC input connector

Figure 3-3AC input and output cables

3–6	975-0337-01-01

Page 32

Image 32

Xantrex Technology IP1012 AL manual Removing and Reconnecting AC Cables, To remove the AC cables, To reconnect

Contents

IP1012 AL IP1012 AL Inverter/Charger with Ignition ProtectionOwner’s Guide Page Owner’s Guide IP1012 AL Inverter/ Charger with Ignition ProtectionAbout Xantrex TrademarksNotice of Copyright Exclusion for DocumentationAbout This Guide PurposeScope AudienceConventions Used Related InformationImportant Safety Information General PrecautionsPrecautions When Working With Batteries Precautions for Using Rechargeable DevicesContents 3 Maintenance1 Introduction 2 OperationTroubleshooting 4 TroubleshootingA Specifications 1 Introduction Inverter/charger Features Operating Features Charger features 2 Operation AC loads Planning for AC LoadsType of Loads DC loads Problem loadsAmbient Temperature Calculating Size of an AC Load Battery condition Factors affecting load Appliance WattsMinutes HoursRunning the Alternator While Operating AC and DC Loads Indication Figure 2-3 Remote switch with indicator lights Using the Remote SwitchSwitch settings The switch shown in Figure 2-3 is used to disable the inverter. TheSwitch The switch indicator lights i.e., LED provide information about theindicators lights the lights will behave like thisOperating the Inverter/Charger Turning the Inverter On and Running LoadsRunning in Extremes Of Hot or Cold Temperatures Restarting After a ShutdownMiscellaneous Hints Battery ChargingUsing Shorepower 3 Maintenance Chapter 3, “Maintenance” provides procedures fordisconnecting the IP1012 AL from the batteries removing or connecting the AC input and output cablesTo remove the terminal cap Maintaining the Inverter/chargerChecking Terminals Disconnecting and Connecting the Batteries Disconnecting WARNING Explosion or FireConnecting To disconnect from the batteryWARNING Correct Fuse Type Replacing the FuseWARNING Possible popping sound and sparks CAUTION Do not overtighten fuse nuts To replace the fuseTo reconnect Removing and Reconnecting AC CablesTo remove the AC cables 4 Troubleshooting Troubleshooting Common ProblemsBlinking Lights on the Remote Switch Troubleshooting reference ContinuedSymptom Possible ProblemTable 4-2 Charger indicator blink patterns Table 4-3 Inverter indicator blink patternsA Specifications All specifications are subject to change without noticePhysical Specifications Physical specificationsInverter Specifications Charger Specifications Charger specificationsTransfer and general specifications Transfer and General SpecificationsCharger specifications Continued Rating Curves and Charging Profiles Figure A-1 Output surge ratingFigure A-2 Charging current versus temperature derating curve PowerFigure A-3 Three-stage charging profile BulkFloat Charge DC VoltagePage Index extension cord see connection cordPage Warranty and Return Information WarrantyDisclaimer ProductExclusions Return Material Authorization PolicyReturn Procedure Out of Warranty Service Information About Your SystemPage Xantrex Technology Inc 1 800 670 0707 Tel toll free NA 1 360 925 5097 Tel direct1 800 994 7828 Fax toll free NA 975-0337-01-01