Manuals / Xerox / Computer Equipment / Printer

Xerox FS 3270 instruction manual Updating Firmware

Models: FS 3270

1 62

Download 62 pages 20.49 Kb

Page 33

FSL Setup via PC's Parallel Port

Xerox FS 3270, User's Guide

8.1. Updating Firmware

The Xerox FS 3270 firmware (complete firmware) may be updated either via the coax line or via centronics input port. For further in formation please contact your i-data distributor.

If errors are detected, the downloading will be terminated and an error message will be printed if possible. If serious errors occur during programming, the firmware has to be downloaded via the share port.

The downloading of firmware is considered complete if no data is received within 30 seconds. The interface will then make a soft re set.

NOTE:

In case of damaged FLASH PROM, try the following procedure:

Boot Download of firmware:

1.Turn the power off

2.Place the rotary switch in the “B” position

3.Turn the power on and note that the READY LED is lit

4.Download the boot firmware (Syntax: “Copy 140.xxx.1 /b”)

5.Download the new firmware. When download is completed and the FLASH PROM is programmed, the LED will start flashing

6.Turn off the power and set the rotary switch in a position different from “A”, “B” or “T” before turning on the power again.

- 33 -

Image 33

Xerox FS 3270 instruction manual Updating Firmware

Contents

Trademarks EMC directivePreface Related ManualsSeptember Table of Contents Table of Contents Xerox FS 3270, Users Guide PCL Driver Default Driver Installation RequirementsIntroduction to Xerox FS PCL or FSL output driverNon-IPC Xerox FS 3270 FeaturesSupported Control Units Items SuppliedXerox FS IPC Upgrade Kit Changing Paper Size Default US/EuropeOperating Environment Xerox FS 3270 IPCInstallation Requirements Xerox FS 3270, Users Guide Rear Panel Installation and Connections of the Xerox FSSerial input Changing the Printer DriverUpgrading to IPC Connecting the Xerox FS 3270 to the PrinterConnecting via RS-232 output Connecting via Centronics outputConnecting to System Xerox FS 3270, Users Guide What if the CU Indicator fails to turn on? Connecting the Xerox FS 3270 to the SystemPCL driver TestingSettings Printout at Power-on PCL mode only TimeoutOperation of Xerox FS Indicators of the Xerox FSCU Contact with Control Unit PAR Parallel inputReady Printer Ready SER Serial input??character Specifying Timeout??%%Y100,30,1B,45%%X1 IdaSetup IPC Programming Printer IRQ HandlingProgramming Xerox FS 3270 non-IPC PCL Driver DefaultSetup Functions Supported in PCL mode ESC Features Where % is the defined ESC characterWhere % is the defined ESC character Send Logo Test functions T-Functions User Settings Functions X-FunctionsEngineering Functions FunctionsSetup Functions Supported in FSL mode ESC Features User Settings Functions X-Functions ??%%Y249,PASSWORD%%Y100,10,’SHARESTRING’%%X1 FSL Setup via Xerox FS 3270 Serial or Parallel Port??%%Y100,10,’SHARESTRING’%%X1 Character conversionLimitations when Y249 is active Activating the Y249 Engineering FunctionDeactivating the Y249 Engineering Function Updating Firmware Recoverable Errors Error MessagesNot in engineering mode Non-Recoverable Hardware Errors Busy Timeout Test PrintoutsPCL Test Printout Gfid CPI= Proportionally Spaced =Active Gfid = FSL Test Printout FSL N/S Appendix a Quick Reference Guide to FSL FunctionsLPI LPI FSL N/SEbcdic Y10 =FSL=PCL Y12 Y13Are wrapped Y22 Y19FF after Y26,n1% = No FF Y35 EAB Y39Y41 Y47 IRQEEPROM/RAM ESCEeprom Y52Y54 Y53Y55 Y56Y71 Y74HEX FSL mode PCL modeAscii HEX N2dataAPL Y79Name Syntax Parameters Deviations Y92 Y91Y93 Y94Y96 Y98APO Y110 Y111Y112 Y114 Y113Y115 Y118RAM Re. T2Data Appendix B Using Serial OUT Use of Xerox FS 3270 serial portExample Cable connections to HP LaserJet Appendix C Selected Xerox Products