Upgrading to IPC | Xerox FS 3270 specification

Connecting to System

Xerox FS 3270, User's Guide

NOTE:

Programming of functions 15, 16, 17, 18 and 24 is not possible via the serial port. These functions have to be programmed either via the coax or via the parallel input port.

2.2. Upgrading to IPC

If you need to upgrade your Xerox FS 3270 with the IPC module, please follow these instruction before proceeding with the installation.

1.Unscrew the 4 screws from the bottom of the converter.

2.Place you hands on each side of the box, bottom facing down and the rear panel facing you. Carefully press open the top cover of the converter.

3.Place the IPC module (main component side facing up) on the PCB of the box. Note that the connector has to be placed on top of the PCB’s connector (to the right on the PCB).

4.Make sure the plastic supports fit in the holes of the IPC module.

5.Press the module gently into position and, while still facing the rear panel, place the top cover precisely above the bottom cover so that all edges are aligned. Press the top cover gently into a locked position.

6.Re-insert the screws and fasten.

7.Now proceed to the actual installation of the converter to the printer and the system.

2.3.Connecting the Xerox FS 3270 to the Printer

CAUTION:

All connections to the Xerox FS 3270 protocol converter should be made while the power is switched OFF.

- 12 -

Image 12

Xerox instruction manual Upgrading to IPC, Connecting the Xerox FS 3270 to the Printer

Contents

EMC directive Trademarks Preface Related ManualsSeptember Table of Contents Table of Contents Xerox FS 3270, Users Guide Installation Requirements PCL Driver Default DriverIntroduction to Xerox FS PCL or FSL output driver Xerox FS 3270 Features Non-IPC Supported Control Units Items SuppliedXerox FS Changing Paper Size Default US/Europe IPC Upgrade KitOperating Environment Xerox FS 3270 IPC Installation Requirements Xerox FS 3270, Users Guide Installation and Connections of the Xerox FS Rear Panel Changing the Printer Driver Serial input Connecting the Xerox FS 3270 to the Printer Upgrading to IPC Connecting via Centronics output Connecting via RS-232 output Connecting to System Xerox FS 3270, Users Guide Connecting the Xerox FS 3270 to the System What if the CU Indicator fails to turn on? Testing PCL driver Timeout Settings Printout at Power-on PCL mode only Indicators of the Xerox FS Operation of Xerox FSCU Contact with Control Unit PAR Parallel input SER Serial input Ready Printer Ready Specifying Timeout ??character ??%%Y100,30,1B,45%%X1 IdaSetup IPC Programming IRQ Handling Printer PCL Driver Default Programming Xerox FS 3270 non-IPC Setup Functions Supported in PCL mode ESC Features Where % is the defined ESC characterWhere % is the defined ESC character Send Logo User Settings Functions X-Functions Test functions T-FunctionsEngineering Functions Functions Setup Functions Supported in FSL mode ESC Features User Settings Functions X-Functions FSL Setup via Xerox FS 3270 Serial or Parallel Port ??%%Y249,PASSWORD%%Y100,10,’SHARESTRING’%%X1??%%Y100,10,’SHARESTRING’%%X1 Character conversion Limitations when Y249 is active Activating the Y249 Engineering FunctionDeactivating the Y249 Engineering Function Updating Firmware Error Messages Recoverable Errors Not in engineering mode Non-Recoverable Hardware Errors Busy Timeout Test PrintoutsPCL Test Printout Gfid CPI= Proportionally Spaced =Active Gfid = FSL Test Printout Appendix a Quick Reference Guide to FSL Functions FSL N/SLPI LPI FSL N/S Ebcdic Y10 =FSL=PCL Y12 Y13Are wrapped Y19 Y22 FF after Y26,n1% = No FF Y35 EAB Y39Y41 IRQ Y47 ESC EEPROM/RAMEeprom Y52 Y53 Y54Y55 Y56 Y71 Y74HEX PCL mode FSL modeAscii HEX N2data Y79 APL Name Syntax Parameters Deviations Y91 Y92Y93 Y94 Y96 Y98APO Y110 Y111Y112 Y113 Y114Y115 Y118 Re. T2 RAM Data Appendix B Using Serial OUT Use of Xerox FS 3270 serial portExample Cable connections to HP LaserJet Appendix C Selected Xerox Products