Manuals / Brands / Home Audio / CD Player / Yamaha / Home Audio / CD Player

Yamaha CDR1000 Monitoring, Metering & Peak Hold, Setting the Meter Response Rate

1 67

Download 67 pages, 969.35 Kb

20 Chapter 3—The Basics

CDR1000—Owner’s Manual

Monitoring

Playback signals are output via the ANALOG OUT, AES/EBU OUT, COAXIAL OUT,

and PHONES.

For recording, the selected input source can be monitored via the ANALOG OUT,

AES/EBU OUT, COAXIAL OUT, and PHONES in Record Standby mode and while

recording.

Use the PHONES LEVEL control to adjust the volume level of the phones.

The recording level for the AES/EBU IN or COAXIAL IN is determined by the source

and cannot be set on the CDR1000. For playback, the AES/EBU OUT and COAXIAL

OUT output digital audio at the same level that it was recorded to disc. For recording,

the level is the same as that received at the AES/EBU IN and COAXIAL IN.

The recording level for the ANALOG IN is set using the REC LEVEL control. This

affects the level of the ANALOG OUT during recording. After recording, the ANALOG

OUT level is ﬁxed, and cannot be adjusted on the CDR1000.

Metering & Peak Hold

Playback and recording signal levels can be metered on the 16-segment meters, with

Peak Hold function, from –60 dB through to –1 dB, and CLIP. For recording, the

selected input source can be metered in Record Standby mode and while recording.

Signal peaks can be checked using the Peak Hold function. When Peak Hold is off,

meter segments lit by signal peaks remain lit for one second. When Peak Hold is on,

however, they remain lit permanently.

1Press the [PEAK HOLD] button to turn on the Peak Hold function.

The PEAK HOLD indicator lights up.

The meter segments lit by the signal peaks remain lit permanently.

2Press the [PEAK HOLD] button again to turn off the Peak Hold function.

The PEAK HOLD indicator goes out.

Setting the Meter Response Rate

The response rate of the level meters can be set to either Slow or Fast using the Utility

Meter parameter.

1Use the [UTILITY] button to select “METER.”

The UTILITY indicator lights up and the response rate setting appears on the display.

2Use the [PREV] or [NEXT] button to select a response rate.

3Press and hold the [UTILITY] button, or press another button to cancel Utility.

Setting Description

SLOW Slow response rate.

FAST Fast response rate.

Contents

Main E PROFESSIONAL AUDIO CD RECORDER Keep This Manual For Future Reference. Owners Manual PROFESSIONAL AUDIO CD RECORDER POWER FCC INFORMATION (U.S.A.) IMPORTANT 1 2 3 JUISTE GEBRUIK EN BEHANDELING V AN BA TTERIJEN i Important Information Warnings Read the Following Before Operating the CDR1000 ii Handling Discs Cautions Note Contents 1 Introduction Transportation Pad Installation About this Manual CDR1000 Features Page Operating Notes Page 2 Touring the CDR1000 I H G Page 8 Display 88 88 88 88 CDR1000 K L Function Buttons A B C 1 2 3 4 10 D E F G Rear Panel A B C D 12 Remote Controller 14 Block Diagram The Basics 15 3 The Basics Hookup Examples Analog Coaxial AES/EBU Connecting the Power Cord Turning On the Power Using the Transportation Pad Installing the Transportation Pad 18 Loading & Unloading Discs Disc Type & Status Using the Remote Controller Installing the Remote Controllers Batteries Setting the Time Display 20 Monitoring Metering & Peak Hold Setting the Meter Response Rate 4 Playback Playing Discs Pausing Playback Stopping Playback 22 Playback Operation Table Selecting Tracks Selecting Tracks Directly Selecting Indexes 24 Searching Using Repeat Playback One-track Repeat Playback All-track Repeat Playback A-B Repeat Playback 5 Recording Preparing to Record Selecting the Input Source 26 Setting the Sampling Rate Converter Setting the Input Delay 28 Setting the UV22 Setting the Copy Bit Recording 30 Recording Operation Table 31 Recording Operation Table 32 Incrementing Track Numbers Manually Incrementing Index Numbers Manually 34 Using Auto Rec Start & Track Increment Inserting a Two-second Mute Inserting a Mute at the Beginning of a Track 36 Inserting a Mute at the End of a Track Applying a Fade In 38 Applying a Fade Out Sync Recording from CD, MD, or DAT 40 One-track Sync Recording Page 42 All-track Sync Recording Page 44 Finalizing Discs Erasing Discs (CD-RW only) 46 6 Other Functions Selecting the AES/EBU OUT Playback Clock Selecting the AES/EBU OUT Playback Clock 47 Note: If the message OUT OF RANGE appears while monitoring, stop and reset the sampling rate. Wordclock out WORD CLOCK IN (wordclock slave, source: WORD) 00 00 00 00 mYGDAI YGDAI Using Digital Output Thru Using Digital Output Thru 49 CDR1000 (source machine) PARALLEL AES/EBU OUT PARALLEL AES/EBU IN AES/EBU OUT AES/EBU IN Using a Footswitch Disabling the Remote Controller Using the Parallel Port Parallel Port Pin Conguration 52 Troubleshooting Troubleshooting 53 54 Appendix Error Messages If the CDR1000 displays an error message, follow the instructions below. Specifications 55 Specications 56 Analog Input Analog Output Digital Audio Input Digital Audio Output Dimensions 58 Glossary Index A B C D O P R S T