TROUBLESHOOTING
Problem | Cause | Remedy | Refer to | |
page | ||||
|
|
| ||
|
|
|
| |
The sound suddenly | The protection circuit has been activated | Check that the impedance selector setting is correct. | 10 | |
goes off. | because of a short circuit, etc. |
|
| |
Check the speaker wires are not touching each other | — | |||
|
| |||
|
| and then turn this unit back on. |
| |
|
|
|
| |
| The sleep timer has turned the unit off. | Turn on the power, and play the source again. | — | |
|
|
|
| |
| The sound is muted. | Press MUTE to cancel a mute. | 20 | |
|
|
|
| |
Only the speaker on | Incorrect cable connections. | Connect the cables properly. If the problem persists, | ||
one side can be |
| the cables may be defective. |
| |
heard. |
|
|
| |
Incorrect balance settings in the BASIC | Adjust the Speaker Level settings. | 17 | ||
| ||||
| menu. |
|
| |
|
|
|
| |
Only the center | When playing a monaural source with a |
|
| |
speaker outputs | CINEMA DSP program, the source signal |
|
| |
substantial sound. | is directed to the center channel, and the |
|
| |
| front and surround speakers output effect |
|
| |
| sounds. |
|
| |
|
|
|
| |
No sound from the | The output level of the center speaker is | Raise the level of the center speaker. | 17 | |
center speaker. | set to minimum. |
|
| |
|
|
|
| |
| “Center” in the SOUND menu is set to | Select the appropriate mode for your center speaker. | 41 | |
| None. |
|
| |
|
|
|
| |
| One of the sound field programs (except | Select another sound field program. | 20 | |
| for 6ch Stereo) has been selected. |
|
| |
|
|
|
| |
No sound from the | The output level of the surround speakers | Raise the output level of the surround speakers. | 17 | |
surround speakers. | is set to minimum. |
|
| |
|
|
|
| |
| “Surround L/R” in the SOUND menu is | Select the appropriate speaker mode for the surround | 41 | |
| set to None. | left and right speakers. |
| |
|
|
|
| |
| A monaural source is being played with | Press STEREO/EFFECT to turn on the sound fields. | — | |
| STEREO/EFFECT set to STEREO. | Then select another sound field program. |
| |
|
|
|
| |
No sound from the | “Surround L/R” in the SOUND menu is | If the speaker mode for the surround left and right | 41 | |
surround back | set to None. | speakers is set to None, the speaker mode for the |
| |
speaker. |
| surround back speaker is automatically set to None. |
| |
|
| Select the appropriate speaker mode for the surround |
| |
|
| left and right speaker mode. |
| |
|
|
|
| |
| “Surround Back” in the SOUND menu is | Select Large or Small. | 41 | |
| set to None. |
|
| |
|
|
|
| |
| PLII/PLIIx is set to “PLII” when playing a | Select PLIIx. Press q/DTS to select a PLIIx sound | 50 | |
| field program. |
| ||
|
|
|
| |
No sound from the | “LFE/Bass Out” in the SOUND menu is | Select SWFR or Both. | 41 | |
subwoofer. | set to FRONT when a Dolby Digital or |
|
| |
| DTS signal is being played. |
|
| |
|
|
|
| |
| “LFE/Bass Out” in the SOUND menu is | Select Both. | 41 | |
| set to SWFR or FRONT when a |
|
| |
| source is being played. |
|
| |
|
|
|
| |
| The source does not contain low bass |
|
| |
| signals. |
|
| |
|
|
|
|
52