Manuals / York / Household Appliance / Air Conditioner

York DJ150 installation manual Power Wiring Detail, Electronic Thermostat Field Wiring

Models: DJ150

1 52

Download 52 pages 10.45 Kb

Page 18

POWER WIRING DETAIL

035-19046-002-B-0104

The internal wiring harnesses furnished with this unit are an integral part of the design certified unit. Field alteration to comply with electrical codes should not be required. If any of the wire supplied with the unit must be replaced, replacement wire must be of the type shown on the wiring diagram and the same minimum gauge as the replaced wire.

A disconnect must be utilized for these units. Factory installed disconnects are available. If installing a disconnect

(field supplied or York International supplied accessory), refer to Figure 3 for the recommended mounting location.

Avoid damage to internal components if drilling holes for disconnect mounting.

NOTE: Since not all local codes allow the mounting of a dis- connect on the unit, please confirm compliance with local code before mounting a disconnect on the unit.

Electrical line must be sized properly to carry the load. USE COPPER CONDUCTORS ONLY. Each unit must be wired with a separate branch circuit fed directly from the meter panel and properly fused.

Refer to Figures 16, 17 and 18 for typical field wiring and to the appropriate unit wiring diagram mounted inside control doors for control circuit and power wiring information.

When connecting electrical power and control wiring to the unit, water-proof connectors must be used so that water or moisture cannot be drawn into the unit during normal operation. The above water-proofing conditions will also apply when installing a field sup- plied disconnect switch.

POWER WIRING DETAIL

Units are factory wired for the voltage shown on the unit nameplate. Refer to Electrical Data Tables 8 and 9 to size power wiring, fuses, and disconnect switch.

Power wiring is brought into the unit through the side of the unit or the basepan inside the curb.

THERMOSTAT1

TERMINALS

RC

RH

Y1

Y2

W1

W2

G

C

X1

X3

2

X4

A1

A2

T

T

TOREMOTESENSOR 2ET04701324IFUSED

UNITTERMINALS

STRIPTB1

R

Y1

Y2

W1

W2

G

C

24Volt

XTransformer

OCC

1ElectronicprogrammableThermostat2ET0770010024(includessubbase).

2TerminalsA1andA2providearelayoutputtoclosetheoutdoor economizerdamperswhenthethermostatswitchestotheset-backposition.

FIGURE 16 - ELECTRONIC THERMOSTAT FIELD WIRING

18	Unitary Products Group

Image 18

York DJ150 installation manual Power Wiring Detail, Electronic Thermostat Field Wiring

Contents

10.8 EER SINGLE PACKAGE AIR CONDITIONERS ANDSINGLE PACKAGE GAS/ELECTRIC UNITS DJ150 12-1/2TON Tested in accordance withTABLE OF CONTENTS 035-19046-002-B-0104LIST OF FIGURES LIST OF TABLESSAFETY CONSIDERATIONS GENERALINSPECTION APPROVALS 2.For outdoor installation onlyREFERENCE RENEWAL PARTS12½ Ton Predator Model Number Nomenclature NOMENCLATURE, ADDITIONAL OPTIONS PRECEDING INSTALLATION INSTALLATIONINSTALLATION SAFETY INFORMATION FIGURE 1 - UNIT SHIPPING BRACKETFIGURE 2 - COMPRESSOR SECTION LIMITATIONSFIGURE 3 - PREDATOR MAGNUM COMPONENT LOCATION TABLE 1 UNIT VOLTAGE LIMITATIONS TABLE 2 UNIT TEMPERATURE LIMITATIONS1.Unit is designed for outdoor installation only RIGGING AND HANDLINGTABLE 5 6 POINT LOAD WEIGHT TABLE 3 UNIT WEIGHTSTABLE 4 4 POINT LOAD WEIGHT CLEARANCESDETAIL A FIGURE 7 - UNIT DIMENSIONSDETAIL C UNIT CLEARANCESFIGURE 8 - BOTTOM DUCT OPENINGS FROM ABOVE 18-1/4 FIGURE 9 - REAR DUCT DIMENSIONSDot Plugs ReturnFIGURE 10 - PREDATOR MAGNUM ROOF CURB DIMENSIONS FIGURE 12 - SIDE PANELS WITH HOLE PLUGSPOWER AND CONTROL WIRING THERMOSTAT WIRINGTABLE 7 CONTROL WIRE SIZES FIGURE 13 - RETURN DOWNFLOW PLENUM WITH PANELPOWER WIRING DETAIL FIGURE 16 - ELECTRONIC THERMOSTAT FIELD WIRINGUNITCONTROL BOARD FIGURE 17 - FIELD WIRING 24 VOLT THERMOSTATSUPPLIED DISCONNECT GROUND LUG THREE PHASE POWER TERMINAL BLOCK TB1 FACTORY OR FIELDFACTORY OR FIELD THREE PHASE POWER SUPPLYCONTACTOR 1M GROUNDSupply TABLE 11 MINIMUM SUPPLY AIR CFM TABLE 10 PHYSICAL DATAOPTIONAL ELECTRIC HEAT ComponentOPTIONAL COIL GUARD SHOWN OPTIONAL GAS HEATTABLE 12 GAS HEAT APPLICATION DATA FIGURE 20 - SIDE ENTRY GAS PIPINGGAS CONNECTION LP UNITS, TANKS AND PIPINGPOWER EXHAUST FACTORY INSTALLED OPTIONSFIELD INSTALLED ACCESSORIES VENT AND COMBUSTION AIRMINIMUM POSITION ADJUSTMENT ENTHALPY SET POINT ADJUSTMENTINDOOR AIR QUALITY AQ FIGURE 22 - ENTHALPY SET POINT CHART FIGURE 23 - HONEYWELL ECONOMIZER CONTROL W7212BLOWER ROTATION FIGURE 24 - BELT ADJUSTMENTPHASING TABLE 14 SUPPLY AIR LIMITATIONSTURNS OPEN NOTES FOR TABLE 15 THROUGH TABLE CHECKING AIR QUANTITY TABLE 19 INDOOR BLOWER SPECIFICATIONSAIR BALANCE METHOD ONESUPPLY AIR DRIVE ADJUSTMENT FIGURE 25 - DRY COIL DELTA PTABLE 21 MOTOR SHEAVE DATUM DIAMETERS OPERATIONTABLE 20 ADDITIONAL STATIC RESISTANCE COOLING SEQUENCE OF OPERATIONHIGH-PRESSURELIMIT SWITCH ECONOMIZER SINGLE OR DUAL WITH POWER EXHAUSTCOOLING OPERATION ERRORS NO OUTDOOR AIR OPTIONSCOMPRESSOR PROTECTION SAFETY CONTROLSLOW-PRESSURELIMIT SWITCH FREEZESTATRESET ELECTRIC HEATING OPERATION ERRORSTABLE 22 ELECTRIC HEAT LIMIT SETTING TEMPERATURE LIMITIGNITION CONTROL BOARD GAS HEATING OPERATION ERRORSGAS HEATING SEQUENCE OF OPERATIONS FIRST STAGE OF HEATINGMain Limit Setting TABLE 24 GAS HEAT LIMIT CONTROL SETTINGSAUXILIARY LIMIT SWITCH ALS PRESSURE SWITCH PSGAS HEAT ANTICIPATOR SETPOINTS START-UPCOOLINGSTART-UPGAS HEAT TABLE 25 GAS HEAT ANTICIPATOR SETPOINTSSHUT DOWN POST START CHECKLISTMANIFOLD GAS PRESSURE ADJUSTMENT CHECKING GAS INPUTTABLE 27 GAS RATE CUBIC FEET PER HOUR ADJUSTMENT OF TEMPERATURE RISE BURNERS/ORIFICES INSPECTION/SERVICINGFIGURE 27 - TYPICAL GAS VALVE PREDATOR MAGNUM FLASH CODES TROUBLESHOOTINGCHARGING THE UNIT TABLE 28 UNIT CONTROL BOARD FLASH CODESPower to FIGURE 28 - BASIC TROUBLESHOOTING FLOWCHARTFIGURE 29 - POWER ON FLOW CHART UnitFIGURE 30 - TRIP FAILURE FLOW CHART COOLING TROUBLESHOOTING GUIDE 035-19046-002-B-0104 035-19046-002-B-0104 GAS HEAT TROUBLESHOOTING GUIDE 035-19046-002-B-0104 035-19046-002-B-0104 Unitary Products GroupNorman Unitary5005 Products