Manuals / Brands / Computer Equipment / Network Card / ZyXEL Communications / Computer Equipment / Network Card

ZyXEL Communications 56K Plus Series Introduction, 1.1ZyXEL Omni 56K Plus modem Overview, 1.2Main Features, Chapter

1 66

Download 66 pages, 714.41 Kb

Omni 56K Plus Series User’s Guide

Chapter 1

Introduction

This chapter introduces you to the features and specifications for the ZyXEL Omni 56K USB Plus and Omni 56K COM Plus modems.

1.1ZyXEL Omni 56K Plus modem Overview

The Omni 56K USB Plus or Omni 56K COM Plus is an analog Data/Fax modem used for Internet access via PSTN line. Models included in this series at the time of writing are the Omni 56K COM Plus and the Omni 56K USB Plus. The difference between these two models is: the Omni 56K COM Plus uses RS-232 Com port interface and the Omni 56K USB Plus uses Universal Serial Bus (USB) connection to a computer. Users can connect the cables without turning off the computer which makes it simple to install the modem. It can run upstream and downstream maximum rates of 56Kbps. The rate selection depends on the line quality, and server side configuration.

1.2Main Features

ZyXEL fifth generation data pump with V.92 capability.

V.92 56K up/down-stream data transmission.

Fast retrain with auto fall-forward and fall-back.

Automatic Data/Fax call detection.

G3 14.4Kbps Fax send/receive.

Support Fax class 1, class 2 and class 2.0 command set.

Handset voice record and play.

Voice digitization and compression.

Voice record via IS101 Command Set

Error correction & data compression.

Microsoft 95/98//98SEMe/2000/XP Windows plug and play compatible (Omni 56K COM Plus only).

Microsoft 98SE/Me/2000/XP Windows USB plug and play compatible (Omni 56K USB Plus only).

Flash EPROM upgradeable.

Introduction

1-1

Contents

Page Copyright Copyright © 2004 by ZyXEL Communications Corporation Disclaimer Trademarks Federal Communications Commission (FCC) Interference Statement Notice Certifications ZyXEL Limited Warranty NOTE Customer Support Table of Contents List of Tables Preface About This User's Manual Related Documentation User’s Guide Feedback Syntax Conventions Control Panels Modem Page Introduction 1.1ZyXEL Omni 56K Plus modem Overview 1.2Main Features Page Specifications and Function Description 2.1Hardware Specifications 2.2Firmware Specifications 2.3Protocol Support 2.4Capability 2.5Data Function 2.5.1 Physical Layer Capability 2.5.2 Flow Control 2.5.3 Hardware CTS/RTS Flow Control 2.5.4 Software XON/XOFF Flow Control 2.5.5 Error Control 2.5.6 Data Compression 2.5.7 Repeat Dial 2.5.8 Cyclic Dial 2.5.9 Caller Number Delivery (Caller ID) Page 2.5.10 Distinctive Ring 2.5.11 Security Function Page 2.6Fax function 2.6.1 Fax Physical Layer Protocol 2.6.2EIA Class 1/Class 2/Class 2.0 Command Set 2.6.3ITU-TT.30 Fax Protocol 2.7Voice Function Page Page Result Codes CARRIER PROTOCOL COMPRESSION CONNECT DTE Page Command Sets 4.1Data command sets 4.1.1 Basic AT Command Sets Page 4.1.2 Extended AT& Command Sets Page Page 4.1.3 Extended AT* Command Sets Page 4.1.4 Extended AT# Command Sets 4.2Fax command sets 4.2.1 Service Class 1 Commands 4.2.2 Service Class 2 Commands Page Page Table 4-10Class 2 Command Responses 4.2.3 Service Class 2.0 Commands Page Page 4.3Voice AT Commands Page 4.4Voice Shielded DTE Commands 4.5Voice Shielded DTE Responses 4.6S-RegisterDescriptions Page Page Page Page Page Page Page Firmware Upgrade 5.1Upgrading by Utility 5.2Upgrading by Terminal Emulation Program 5.2.1 Upgrading Using Bitware Example Page Send Send file – Select Protocol Xmodem Settings… XModem Checksum 5.2.2 Upgrading Using HyperTerminal Example Connection Description Connect to COM Properties Page Transfer Send File Page Page Index