Omni 56K II and Omni 56K Plus II User’s Guide
COMMAND | BIT | DEC | HEX | FUNCTION AND DESCRIPTION | REF. |
|
|
|
|
|
|
|
| 6 | 6 | The speaker is ON after the last digit is dialed out the | M3 |
|
|
|
| until carrier is detected. |
|
|
|
|
|
|
|
| 3 | 0 | 0 | DSR is always ON (default). | &S0 |
|
|
|
|
|
|
|
| 8 | 8 | According to CCITT (see also S44.4, S41.5). | &S1 |
|
|
|
|
|
|
| 4 | 0 | 0 | CD is always ON. | &C0 |
|
|
|
|
|
|
|
| 16 | 10 | CD tracks the presence of the data carrier (see also | &C1 |
|
|
|
| S38.3) (default). |
|
| 5 | 0 | 0 | CTS follows RTS in synchronous mode. The response | &R0 |
|
|
|
| delay is set in S26. |
|
|
|
|
|
|
|
|
| 32 | 20 | Ignore RTS (CTS always ON) in synchronous mode. | &R1 |
|
|
|
| (Default) |
|
|
|
|
|
|
|
| 0 | 0 | Assume DTR is always ON. | &D0 | |
|
|
|
|
|
|
|
| 64 | 40 | 108.1, DTR | &D1 |
|
|
|
| dial the default number. |
|
|
| 128 | 80 | 108.2 Data Terminal Ready, DTR OFF causes the | &D2 |
|
|
|
| modem to hang up and return to the command state |
|
|
|
|
| (default) |
|
|
| 192 | C0 | 108.2, DTR OFF causes the modem to hang up and | &D3 |
|
|
|
| reset the modem to profile 0 after the DTR is dropped. |
|
|
|
|
|
|
|
S23= | bit | dec | hex | +105 | |
|
|
|
|
|
|
| 0 | 0 | 0 | Command echo disabled. | E0 |
|
|
|
|
|
|
|
| 1 | 1 | Command echo enabled (default). | E1 |
|
|
|
|
|
|
| 1 | 0 | 0 | Tone dial (default). | T |
|
|
|
|
|
|
|
| 2 | 2 | Pulse dial. | P |
|
|
|
|
|
|
| 2 | 0 | 0 | Pulse dial make/break ratio = 39% / 61% (default). | &P0 |
|
|
|
|
|
|
|
| 4 | 4 | Pulse dial make/break ratio = 33% / 67%. | &P1 |
|
|
|
|
|
|
| 0 | 0 | ATX0 (see result code table). | X0 | |
|
|
|
|
|
|
|
| 8 | 8 | ATX18 | X1 |
|
|
|
|
|
|
|
| 16 | 10 | ATX2 | X2 |
|
|
|
|
|
|
|
| 24 | 18 | ATX3 | X3 |
|
|
|
|
|
|
Command Sets |