Husqvarna 15V2s AWD manual Cleaning, Removing of the machine hoods

Page 20

Maintenance

Cleaning

Clean the machine directly after use. It is much easier to wash off grass cuttings before they dry.

Oily dirt can be removed using a cold degreasing agent. Spray on a thin layer.

Rinse at normal water pressure.

Do not direct the jet towards electrical components or bearings.

Do not rinse hot surfaces such as the engine and exhaust system.

It is recommended that you start the engine and run the mower for a short period after cleaning, so that any remaining water is blown off.

Lubricate the machine if necessary after cleaning. Carry out extra lubrication when the bearings have been exposed to a degreaser or a water jet.

IMPORTANT INFORMATION

Avoid using a high pressure washer or a steam cleaner. There is a major risk of water penetrating into bearings and electrical connections. Corrosion attack can result, which will lead to running problems. Cleaning additives generally aggravate the damage.

Removing of the machine hoods

Engine cover

The engine becomes accessible for service when the engine cover is opened.

Fold the seat forward, loosen the rubber strap under seat and fold the cover backwards.

Front cover

Release the clip on the front hood and lift off the fender.

Right-hand fender

Remove the accelerator knob (1), screws (2 and 3), and remove the cover.

Left-hand fender

Remove the screws holding the wing cover (2) and lift off the cover.

Checking and adjusting the steering wires

The steering is controlled by means of wires.

These can in time become slack, which implies that the adjustment of the steering becomes altered.

Check and adjust the steering as follows:

20 – English

Image 20

Contents Rider 15V2 Rider 15V2 AWD Rider 15V2s AWD EnglishContents After the ﬁrst 8 hours Service journalPre-delivery service Introduction Dear CustomerDriving and transport on public roads TowingGood service Serial NumberKEY to Symbols SymbolsBrake Starting instructions Safety Instructions Safety instructionsInsure your Rider General useDriving on slopes This is what you doMaintenance ChildrenTransport What is WHAT? Location of the controlsPresentation Cutting height adjustment lever Cutting unitLifting lever for the cutting unit LightsExercise care and refuel outdoors see safety instructions FuellingRelease lever Release lever Rider 15V2 AWDStart the engine DrivingBefore starting Starting the engine with a weak battery Connecting the jump leadsDriving the Rider Remove the cables in the reverse orderOther objects which can be thrown out by the blades Cutting tipsStop the engine Maintenance Maintenance scheduleRemoving of the machine hoods CleaningChecking and adjusting the steering wires Adjusting the parking brake Rider Adjusting the parking brake Rider 15V2 AWDChecking and adjusting of throttle wire Can result in reduced braking abilityChecking and adjusting the choke wire Replacement of fuel ﬁlterReplacing the air ﬁlter Cool before starting to replace the air ﬁlterCheck the level of the battery acid Dry-charged battery Checking the fuel pump’s air ﬁlterIgnition system Replacing the spark plugCheck the safety system Replacing the light bulbs Main fuseWhen the engine is running. Mind your ﬁngers Checking the tyre pressureChecking the engine’s cooling air intake Fitting the cutting headRemoving the cutting unit Trapping your handReplacing the cutting unit belts Adjusting the parallelism of the cutting unitChecking the cutting unit’s parallelism Service position for the cutting unit Placing in the service positionRemoving the BioClip plug Restoring from service positionChecking the blades Lubrication Checking the engine’s oil levelChanging the oil ﬁlter Replacing the engine oilGeneral lubrication Lubricating the belt adjusterChecking the transmission oil level Troubleshooting schedule Problem ProcedureService StorageWinter storage GuardTechnical data EC-declaration of conformity Applies to Europe only Page ´z+S!r¶6H¨ Page 1151018-26 ´z+S!r¶6H¨ ´z+S!r¶6H¨