Husqvarna 15V2s AWD manual Fuelling, Release lever Rider 15V2 AWD

Page 15

PRESENTATION

The seat can also be adjusted lengthways.

To adjust move the lever under the front edge of the seat to the left, so that the seat can be moved forward or backwards to the required position.

Fuelling

The engine runs on unleaded petrol with a minimum octane rating of 87 (not mixed with oil). We recommend the use of biodegradable alkylate petrol. (max. methanol 5%, max. ethanol 10%, max. MTBE 15%)

Do not fill the tank completely, leave an expansion area of at least 2.5 cm (1“).

WARNING! Petrol is highly inflammable.

!Exercise care and refuel outdoors (see safety instructions).

IMPORTANT!

Do not use the fuel tank as a support area.

Release lever

The release control must be pulled out in order for the machine to be moved when the engine is shutoff.

Should you attempt to drive the machine with the clutch controls pulled out it will not move. The drive on the axle is disengaged when one of the controls is pulled out.

Pull the controls to the end positions, do not use an intermediate position.

Release lever Rider 15V2 AWD

Rider 15V2 AWD has one control for the front axle and one control for the rear axle.

IMPORTANT!

Always drive the machine with both clutch controls pressed in.

Clutch control, rear axle

-Control drawn out, drive system disengaged.

-Control depressed, drive system engaged.

Clutch control, front axle

The control is positioned on the inside of the left front wheel.

-Rear control (pulled out), drive system disengaged.

-Front control (pushed in), drive system engaged.

Release lever Rider 15V2

Pull out the control to disengage the drive system. Push in the control to engage to the drive system.

English – 15

Image 15
Contents English Rider 15V2 Rider 15V2 AWD Rider 15V2s AWDContents Service journal Pre-delivery serviceAfter the first 8 hours Towing IntroductionDear Customer Driving and transport on public roadsSerial Number Good serviceSymbols KEY to SymbolsBrake Starting instructions General use Safety InstructionsSafety instructions Insure your RiderThis is what you do Driving on slopesChildren MaintenanceTransport Location of the controls What is WHAT?Presentation Lights Cutting height adjustment leverCutting unit Lifting lever for the cutting unitRelease lever Rider 15V2 AWD Exercise care and refuel outdoors see safety instructionsFuelling Release leverDriving Before startingStart the engine Remove the cables in the reverse order Starting the engine with a weak batteryConnecting the jump leads Driving the RiderCutting tips Stop the engineOther objects which can be thrown out by the blades Maintenance schedule MaintenanceCleaning Checking and adjusting the steering wiresRemoving of the machine hoods Can result in reduced braking ability Adjusting the parking brake RiderAdjusting the parking brake Rider 15V2 AWD Checking and adjusting of throttle wireCool before starting to replace the air filter Checking and adjusting the choke wireReplacement of fuel filter Replacing the air filterReplacing the spark plug Check the level of the battery acid Dry-charged batteryChecking the fuel pump’s air filter Ignition systemCheck the safety system Main fuse Replacing the light bulbsFitting the cutting head When the engine is running. Mind your fingersChecking the tyre pressure Checking the engine’s cooling air intakeTrapping your hand Removing the cutting unitAdjusting the parallelism of the cutting unit Checking the cutting unit’s parallelismReplacing the cutting unit belts Placing in the service position Service position for the cutting unitRestoring from service position Checking the bladesRemoving the BioClip plug Replacing the engine oil LubricationChecking the engine’s oil level Changing the oil filterLubricating the belt adjuster Checking the transmission oil levelGeneral lubrication Problem Procedure Troubleshooting scheduleGuard ServiceStorage Winter storageTechnical data EC-declaration of conformity Applies to Europe only Page ´z+S!r¶6H¨ Page 1151018-26 ´z+S!r¶6H¨ ´z+S!r¶6H¨