Husqvarna 15V2s AWD Introduction, Dear Customer, Driving and transport on public roads, Towing

Page 4

INTRODUCTION

Dear Customer,

Thank you for choosing a Husqvarna Rider. Husqvarna Riders are built to a unique design with a front-mounted cutting unit and a patented rear-wheel steering system. Riders are designed for maximum efficiency even in small or confined areas. The closely grouped controls and pedal-operated hydrostatic transmission also contribute to the performance of this machine.

We hope you will find this operator’s manual very useful. By following its instructions (on operation, service, maintenance, etc.) you will significantly extend the life of the machine and even its second-hand value.

When you sell your Rider, make sure you pass on the operator’s manual to the new owner.

The last chapter in the operator’s manual consists of a Service Journal. Make sure that all service work and repairs are recorded. A well-documented service history reduces the costs of seasonal maintenance and influences the second-hand value of the machine. Bring the operator’s manual with the Rider when bringing it to a workshop for service procedures.

Driving and transport on public roads

Check the relevant road traffic regulations before driving the machine on a public road. If transporting the machine on another vehicle always use approved securing devices and make sure that the machine is securely held.

Towing

When your machine is equipped with a hydrostatic transmission you should, if necessary, only tow the machine over short distances and at a low speed, otherwise there is a risk of damaging the transmission.

The power transmission must be disengaged when towing, see the instructions under the heading Clutch control.

Use

This machine is designed solely for cutting grass on conventional lawns and other cleared and leveled ground without obstacles, as rocks, stumps etc., and, in conjunction with accessories supplied by the manufacturer even for other special tasks for which instructions are delivered with the accessory. Use in any other way is considered as contrary to the intended use. Compliance with and strict adherence to the conditions of operation, service and repair as specified by the manufacturer also constitute essential elements of the intended use.

This machine should be operated, serviced and repaired only by persons who are familiar with its particular characteristics and who are acquainted with the relevant safety procedures.

Accident prevention regulations, all other generally recognised regulations on safety and occupational medicine, and all road traffic regulations must be observed at all times.

Any arbitrary modifications carried out to this machine may relieve the manufacturer of liability for any resulting damage or injury.

4 – English

Image 4
Contents Rider 15V2 Rider 15V2 AWD Rider 15V2s AWD EnglishContents Pre-delivery service Service journalAfter the first 8 hours Introduction Dear CustomerDriving and transport on public roads TowingGood service Serial NumberKEY to Symbols SymbolsBrake Starting instructions Safety Instructions Safety instructionsInsure your Rider General useDriving on slopes This is what you doMaintenance ChildrenTransport What is WHAT? Location of the controlsPresentation Cutting height adjustment lever Cutting unitLifting lever for the cutting unit LightsExercise care and refuel outdoors see safety instructions FuellingRelease lever Release lever Rider 15V2 AWDBefore starting DrivingStart the engine Starting the engine with a weak battery Connecting the jump leadsDriving the Rider Remove the cables in the reverse orderStop the engine Cutting tipsOther objects which can be thrown out by the blades Maintenance Maintenance scheduleChecking and adjusting the steering wires CleaningRemoving of the machine hoods Adjusting the parking brake Rider Adjusting the parking brake Rider 15V2 AWDChecking and adjusting of throttle wire Can result in reduced braking abilityChecking and adjusting the choke wire Replacement of fuel filterReplacing the air filter Cool before starting to replace the air filterCheck the level of the battery acid Dry-charged battery Checking the fuel pump’s air filterIgnition system Replacing the spark plugCheck the safety system Replacing the light bulbs Main fuseWhen the engine is running. Mind your fingers Checking the tyre pressureChecking the engine’s cooling air intake Fitting the cutting headRemoving the cutting unit Trapping your handChecking the cutting unit’s parallelism Adjusting the parallelism of the cutting unitReplacing the cutting unit belts Service position for the cutting unit Placing in the service positionChecking the blades Restoring from service positionRemoving the BioClip plug Lubrication Checking the engine’s oil levelChanging the oil filter Replacing the engine oilChecking the transmission oil level Lubricating the belt adjusterGeneral lubrication Troubleshooting schedule Problem ProcedureService StorageWinter storage GuardTechnical data EC-declaration of conformity Applies to Europe only Page ´z+S!r¶6H¨ Page 1151018-26 ´z+S!r¶6H¨ ´z+S!r¶6H¨