Husqvarna 15V2s AWD manual Checking the blades, Removing the BioClip plug

Page 30

Maintenance

8Lift of the drive belt. Then pull out the pin.

9Pull the frame forwards and reﬁt the pin.

10Grasp the front edge of the cutting unit, pull out and raise into the service position.

If the cylindrical bolt, which is now holding the cutting unit is removed, the cutting unit can be lifted off.

Restoring from service position

To leave the service position, reverse the procedures set out in Placing in the service position. Make sure that the cutting unit’s ”lug” (3) enters the loop correctly on the underside of the machine, see diagram.

Checking the blades

To achieve the best mowing results it is important that the blades are undamaged and well-sharpened.

Check that the blades’ attachment screws are tight.

IMPORTANT INFORMATION Replacing or sharpening the blades should be conducted by an authorised service workshop.

The blades should be balanced after sharpening.

Damaged blades should be replaced when hitting obstacles that result in a breakdown. Let the servicing dealer judge whether the blade can be repaired/ground or must be discarded.

Removing the BioClip plug

To change a Combi unit from BioClip function to cutting unit with rear ejection, remove the BioClip plug located under the unit with three screws.

1Put the unit in the service position, see Placing in the service position.

2Remove the three screws holding the BioClip plug, and remove the plug.

3Tip: Fit three full-thread screws M8x15 mm in the screw holes to protect the threads.

4Replace the unit in normal position. Fit the BioClip plug in the reverse order.

30 – English

Image 30

Contents Rider 15V2 Rider 15V2 AWD Rider 15V2s AWD EnglishContents Service journal Pre-delivery serviceAfter the ﬁrst 8 hours Driving and transport on public roads IntroductionDear Customer TowingGood service Serial NumberKEY to Symbols SymbolsBrake Starting instructions Insure your Rider Safety InstructionsSafety instructions General useDriving on slopes This is what you doMaintenance ChildrenTransport What is WHAT? Location of the controlsPresentation Lifting lever for the cutting unit Cutting height adjustment leverCutting unit LightsRelease lever Exercise care and refuel outdoors see safety instructionsFuelling Release lever Rider 15V2 AWDDriving Before startingStart the engine Driving the Rider Starting the engine with a weak batteryConnecting the jump leads Remove the cables in the reverse orderCutting tips Stop the engineOther objects which can be thrown out by the blades Maintenance Maintenance scheduleCleaning Checking and adjusting the steering wiresRemoving of the machine hoods Checking and adjusting of throttle wire Adjusting the parking brake RiderAdjusting the parking brake Rider 15V2 AWD Can result in reduced braking abilityReplacing the air ﬁlter Checking and adjusting the choke wireReplacement of fuel ﬁlter Cool before starting to replace the air ﬁlterIgnition system Check the level of the battery acid Dry-charged batteryChecking the fuel pump’s air ﬁlter Replacing the spark plugCheck the safety system Replacing the light bulbs Main fuseChecking the engine’s cooling air intake When the engine is running. Mind your ﬁngersChecking the tyre pressure Fitting the cutting headRemoving the cutting unit Trapping your handAdjusting the parallelism of the cutting unit Checking the cutting unit’s parallelismReplacing the cutting unit belts Service position for the cutting unit Placing in the service positionRestoring from service position Checking the bladesRemoving the BioClip plug Changing the oil ﬁlter LubricationChecking the engine’s oil level Replacing the engine oilLubricating the belt adjuster Checking the transmission oil levelGeneral lubrication Troubleshooting schedule Problem ProcedureWinter storage ServiceStorage GuardTechnical data EC-declaration of conformity Applies to Europe only Page ´z+S!r¶6H¨ Page 1151018-26 ´z+S!r¶6H¨ ´z+S!r¶6H¨