Husqvarna 15V2s AWD manual Troubleshooting schedule, Problem Procedure

Page 33

Troubleshooting schedule
Problem	Procedure
Engine does not start	There is no fuel in the fuel tank
	Spark plug defective
	Faulty spark plug connections or interchanged cables
	Dirt in the carburettor or fuel line
	Starter motor does not turn over the engine
Starter motor does not turn over the engine	Battery ﬂat
	Bad contact between the cable and battery
	Lift lever for cutting unit in wrong position
	Main fuse blown.
	This fuse is in front of the battery, under the battery cover.
	Ignition lock faulty
	Hydrostat pedals not in the neutral position
	Faulty starter motor
Engine does not run smoothly	Faulty spark plug.
	Carburettor incorrectly set
	Air ﬁlter clogged
	Fuel tank vent blocked
	Ignition key defective
	Dirt in the carburettor or fuel line
	Choking or incorrectly adjusted throttle cable
Engine seems to have no power	Air ﬁlter clogged
	Faulty spark plug.
	Dirt in the carburettor or fuel line
	Carburettor incorrectly set
	Choking or incorrectly adjusted throttle cable
Engine overheats	Engine overloaded
	Air intake or cooling ﬂanges blocked
	Fan damaged
	Too little or no oil in engine
	Ignition defective
	Faulty spark plug.
Battery does not charge	One or more battery cells faulty
	Poor contact on the battery terminal cable connectors
Machine vibrates	Blades are loose
	Engine is loose
	One or more blades unbalanced, caused by damage or poor balancing after
	sharpening
Uneven mowing	Blades blunt
	Cutting unit skew
	Long or wet grass
	Grass blockage under hood
	Different tyre pressures on right and left sides
	Over-speeding
	Engine speed too low
	Drive belt slipping

English – 33

Image 33

Contents English Rider 15V2 Rider 15V2 AWD Rider 15V2s AWDContents Service journal Pre-delivery serviceAfter the ﬁrst 8 hours Dear Customer IntroductionDriving and transport on public roads TowingSerial Number Good serviceSymbols KEY to SymbolsBrake Starting instructions Safety instructions Safety InstructionsInsure your Rider General useThis is what you do Driving on slopesChildren MaintenanceTransport Location of the controls What is WHAT?Presentation Cutting unit Cutting height adjustment leverLifting lever for the cutting unit LightsFuelling Exercise care and refuel outdoors see safety instructionsRelease lever Release lever Rider 15V2 AWDDriving Before startingStart the engine Connecting the jump leads Starting the engine with a weak batteryDriving the Rider Remove the cables in the reverse orderCutting tips Stop the engineOther objects which can be thrown out by the blades Maintenance schedule MaintenanceCleaning Checking and adjusting the steering wiresRemoving of the machine hoods Adjusting the parking brake Rider 15V2 AWD Adjusting the parking brake RiderChecking and adjusting of throttle wire Can result in reduced braking abilityReplacement of fuel ﬁlter Checking and adjusting the choke wireReplacing the air ﬁlter Cool before starting to replace the air ﬁlterChecking the fuel pump’s air ﬁlter Check the level of the battery acid Dry-charged batteryIgnition system Replacing the spark plugCheck the safety system Main fuse Replacing the light bulbsChecking the tyre pressure When the engine is running. Mind your ﬁngersChecking the engine’s cooling air intake Fitting the cutting headTrapping your hand Removing the cutting unitAdjusting the parallelism of the cutting unit Checking the cutting unit’s parallelismReplacing the cutting unit belts Placing in the service position Service position for the cutting unitRestoring from service position Checking the bladesRemoving the BioClip plug Checking the engine’s oil level LubricationChanging the oil ﬁlter Replacing the engine oilLubricating the belt adjuster Checking the transmission oil levelGeneral lubrication Problem Procedure Troubleshooting scheduleStorage ServiceWinter storage GuardTechnical data EC-declaration of conformity Applies to Europe only Page ´z+S!r¶6H¨ Page 1151018-26 ´z+S!r¶6H¨ ´z+S!r¶6H¨