ResMed AutoSet CS 2 Using DC Power to RUN the Autoset CS2, Inserting anti-bacterial filters

Page 22

Anti-bacterial filters

Figure 10: Inserting anti-bacterial filters

USING DC POWER TO RUN THE AUTOSET CS2

The AUTOSET CS2 can be run on DC current in case of power failure or for portable use. ResMed supplies a convertor that allows a 12V battery to be connected to the DC input of the AUTOSET CS2. The converter can also be plugged in to a power source in a car or plane. When using DC current, power is turned on and off via the switch on the connector to the power source, not the power switch at the back of the AUTOSET CS2. The DC converter is a separate accessory that can be purchased through your ResMed distributor.

The humidifer heater will be automatically disabled when the AUTOSET CS2 is operating from the DC supply.

Power consumption of the AUTOSET CS2 varies with treatment settings. A typical current of between 2.5A and 3.0A will be drawn from a 12V battery during use. Adequate battery type and sizing is required before operation on DC, and it is recommended that ResMed’s Technical Services division be contacted for information on your specific application.

CAUTION

! The AUTOSET CS2 uses 30V DC power. Only connect the AUTOSET CS2 to DC power using the ResMed DC-DC convertor specified for this application.

18

Image 22
Contents AutoSet CS EUR AutoSet CS Page Autoset CS Page Table of Contents Cleaning and Maintenance USER/OWNER Responsibility IntroductionAutoset CS2 Medical InformationPage Quick Setup Guide Page Autoset CS2 System Autoset CS2 ComponentsConnect this end Connect the power cord Assembling the Autoset CS2 SystemConnect air tubing Humidifiers Attach the mask to the air tubingConnecting a Humidifier Humidaire Perform the Air Circuit Learn function see Reslink ANTI-BACTERIAL FilterUsing DC Power to RUN the Autoset CS2 Inserting anti-bacterial filtersUsing Supplemental Oxygen Oxygen tube attached to Mirage FFMS2 and Ultra Mirage masksPage Starting Treatment Using the Autoset CS2Standby Mode Stopping TreatmentSTART/STOP KEY Control Panel FunctionsLCD Screen UP/DOWN KEYLeft KEY Green Adjusting SettingsAlarm Leds and Alarm Mute Right KEY REDYou wish to change the sound level for the alarms ExampleMenus Navigating the Patient menuMask Learn CircuitLeak Alert SmartstopSound Level Usage Mask FITAverage Pressure Smart DataTreatment Screens ApneaPage If a LOW Pressure Alarm Sounds AlarmsTriggered by If a High Leak Alarm Sounds If a Power Fail Alarm SoundsIf a High Pressure Alarm Sounds Will Clear WhenIf AN Insufficient Pressure Support Alarm Sounds If a Flow Blocked Alarm SoundsPage Daily Cleaning and MaintenanceWeekly Periodically AIR FilterServicing Fitting the FilterPage Troubleshooting Problem Possible cause SolutionPage Glossary Page Technical Specifications Leak exceeds 30 L/min for more than 20 seconds Max Pressure Environmental information English Next Recommended separation distance Separation distance according to frequency of transmitter Limited Warranty Product Warranty PeriodPage Index Page Manuel Utilisateur Page Sommaire Nettoyage ET Entretien Responsabilite DE L’UTILISATEUR/DU Proprietaire Informations MedicalesPrecautions AvertissementsGuide D’INSTALLATION Rapide Page Autoset CS2 Composants DE L’AUTOSET CS2Raccordez cette extrémité Avertissement Montage DE L’AUTOSET CS2Raccordez le circuit respiratoire Humidificateurs Montage de l’AutoSet CS2Voir « Début du traitement » De l’AutoSet CS2 Avertissement Filtre Antibacterien Utilisation D’UNE Alimentation CC Avec L’AUTOSET CS2 Mise en place des filtres antibactériensAvertissements Utilisation D’OXYGENE SupplementairePage Debut DU Traitement Mode D’ATTENTEUtilisation DE L’AUTOSET CS2 Arret DU TraitementEcran LCD Touche DE Deplacement Vers LE HAUT/BASFonctions DU Panneau DE Controle Touche MARCHE/ARRETTouche DE Gauche Verte Temoins D’ALARME ET Desactivation DE L’ALARMEModification DES Reglages Touche DE Droite RougeVous souhaitez modifier le niveau du son pour les alarmes ExempleNavigation dans le menu Patient Masque IDENT. CircuitAlarme Fuite AI FaiblePression Moyenne Ajustement DU MasqueUtilisation RETRO-ECL Ecrans DE TraitementLangue Remarquecibl nest pas un paramètre utilisé en mode Cpap LES Alarmes Declenchee LorsqueSI UNE Alarme DE Pression Elevee SE Declenche SI UNE Alarme DE Pression Basse SE DeclencheSI UNE Alarme DE Panne DE Courant SE Declenche ’ARRETE LorsqueSI L’ALARME D’AIDE Inspiratoire Insuffisante SE Declenche SI UNE Alarme DE Fuite Importante SE DeclencheSI L’ALARME DE Debit Bloque SE Declenche Page Quotidien Nettoyage ET EntretienHebdomadaire Periodique Démontage du circuit respiratoire pour le nettoyageFiltre a AIR Mise EN Place DU FiltreEntretien Problème Cause possible Solution Strategie DE DepannagePage Glossaire Page Caracteristiques Cm H2O, si cette valeur est inférieure Pression Max Informations concernant l’environnement 101 102 103 104 Garantie Limitee Produit Durée de la Garantie106 Index 108

AutoSet CS 2 specifications

ResMed AutoSet CS 2 is a state-of-the-art device designed for individuals suffering from complex sleep apnea and central sleep apnea. This advanced treatment solution leverages innovation and cutting-edge technology to provide optimal comfort and effective therapy during sleep, ultimately helping users achieve a better quality of life.

One of the standout features of the AutoSet CS 2 is its sophisticated auto-adjusting pressure capabilities. The device automatically detects and responds to the patient's breathing patterns throughout the night, adjusting the pressure levels in real time to ensure that airway obstructions are effectively managed. This technology helps prevent both hypopneas and apneas, providing a seamless therapy experience.

The device is equipped with ResMed's proprietary Easy-Breathe technology, which allows for smooth pressure changes that mimic the user's natural breathing cycle. This feature enhances user comfort, making it easier for individuals to adapt to CPAP therapy and continue using the device consistently over time.

Another remarkable characteristic of the AutoSet CS 2 is its integrated wireless connectivity. This connectivity facilitates remote monitoring and data sharing with healthcare professionals, enabling more effective management of treatment progress. By analyzing sleep data, providers can make informed adjustments to therapy, ensuring that the patient receives the best possible care.

The AutoSet CS 2 also includes a user-friendly interface with a high-resolution color display, making it easy for users to navigate menus and access vital information about their sleep patterns and therapy effectiveness. With its compact design, the device is portable and can easily be used at home or while traveling.

In terms of comfort, the AutoSet CS 2 features a quiet operation, enabling a peaceful sleep environment. It is compatible with various masks, providing flexibility for users to find the best fit for their personal comfort preferences.

Overall, the ResMed AutoSet CS 2 is a leading choice for individuals with complex sleep apnea. With its combination of advanced features, user-centric design, and state-of-the-art technology, it empowers users to take control of their sleep and improve their overall health and well-being.