ResMed AutoSet CS 2 user manual If AN Insufficient Pressure Support Alarm Sounds

Page 37

WILL STOP WHEN:

•the mask leak has been rectified.

NOTE The High Leak alarm can be turned off in the Leak Alert option in the Settings menu.

INSUFFICIENT PRESSURE SUPPORT ALARM

TRIGGERED BY:

•air pressure at the mask has failed to reach an expected level for 3 breaths

•the Air Circuit Learn function (page 26) has not been run after adding a new component (eg new mask, humidifier) to the system.

IF AN INSUFFICIENT PRESSURE SUPPORT ALARM SOUNDS:

•check that the pressure sensor tubing is not kinked

•check that the pressure sensor tubing is properly connected

•run LEARN CIRCUIT.

WILL STOP WHEN:

•the pressure sensor tubing is unobstructed and properly connected to the flow generator and mask

•treatment is stopped (Start/Stop key or SMARTSTOP)

•the AUTOSET CS2 is turned off.

FLOW BLOCKED ALARM

TRIGGERED BY:

•blockage in air circuit

IF A FLOW BLOCKED ALARM SOUNDS:

1.The treatment will stop.

2.Turn power off.

3.Check whether there is a blockage in the air circuit.

4.Remove blockage.

5.Turn power back on.

6.If the Flow blocked alarm activates repeatedly, discontinue use and return to ResMed for servicing. If the alarm does not recur, then continue to use as normal.

WILL STOP WHEN:

•blockage is removed.

ENGLISH

THE ALARMS

33

Page 36 Page 38
Image 37
Page 36 Page 38
Contents AutoSet CS EUR AutoSet CS Page Autoset CS Page Table of Contents Cleaning and Maintenance Autoset CS2 IntroductionUSER/OWNER Responsibility Medical InformationPage Quick Setup Guide Page Autoset CS2 Components Autoset CS2 SystemConnect this end Assembling the Autoset CS2 System Connect the power cordConnect air tubing Attach the mask to the air tubing HumidifiersConnecting a Humidifier Humidaire Perform the Air Circuit Learn function see ANTI-BACTERIAL Filter ReslinkInserting anti-bacterial filters Using DC Power to RUN the Autoset CS2Oxygen tube attached to Mirage FFMS2 and Ultra Mirage masks Using Supplemental OxygenPage Standby Mode Using the Autoset CS2Starting Treatment Stopping TreatmentLCD Screen Control Panel FunctionsSTART/STOP KEY UP/DOWN KEYAlarm Leds and Alarm Mute Adjusting SettingsLeft KEY Green Right KEY REDExample You wish to change the sound level for the alarmsNavigating the Patient menu MenusLearn Circuit MaskLeak Alert SmartstopSound Level Average Pressure Mask FITUsage Smart DataApnea Treatment ScreensPage If a LOW Pressure Alarm Sounds AlarmsTriggered by If a High Pressure Alarm Sounds If a Power Fail Alarm SoundsIf a High Leak Alarm Sounds Will Clear WhenIf a Flow Blocked Alarm Sounds If AN Insufficient Pressure Support Alarm SoundsPage Daily Cleaning and MaintenanceWeekly AIR Filter PeriodicallyFitting the Filter ServicingPage Problem Possible cause Solution TroubleshootingPage Glossary Page Technical Specifications Leak exceeds 30 L/min for more than 20 seconds Max Pressure Environmental information English Next Recommended separation distance Separation distance according to frequency of transmitter Product Warranty Period Limited WarrantyPage Index Page Manuel Utilisateur Page Sommaire Nettoyage ET Entretien Informations Medicales Responsabilite DE L’UTILISATEUR/DU ProprietaireAvertissements PrecautionsGuide D’INSTALLATION Rapide Page Composants DE L’AUTOSET CS2 Autoset CS2Raccordez cette extrémité Montage DE L’AUTOSET CS2 AvertissementRaccordez le circuit respiratoire Montage de l’AutoSet CS2 HumidificateursVoir « Début du traitement » De l’AutoSet CS2 Avertissement Filtre Antibacterien Mise en place des filtres antibactériens Utilisation D’UNE Alimentation CC Avec L’AUTOSET CS2Utilisation D’OXYGENE Supplementaire AvertissementsPage Utilisation DE L’AUTOSET CS2 Mode D’ATTENTEDebut DU Traitement Arret DU TraitementFonctions DU Panneau DE Controle Touche DE Deplacement Vers LE HAUT/BASEcran LCD Touche MARCHE/ARRETModification DES Reglages Temoins D’ALARME ET Desactivation DE L’ALARMETouche DE Gauche Verte Touche DE Droite RougeExemple Vous souhaitez modifier le niveau du son pour les alarmesNavigation dans le menu Patient IDENT. Circuit MasqueAI Faible Alarme FuitePression Moyenne Ajustement DU MasqueUtilisation RETRO-ECL Ecrans DE TraitementLangue Remarquecibl nest pas un paramètre utilisé en mode Cpap Declenchee Lorsque LES AlarmesSI UNE Alarme DE Panne DE Courant SE Declenche SI UNE Alarme DE Pression Basse SE DeclencheSI UNE Alarme DE Pression Elevee SE Declenche ’ARRETE LorsqueSI L’ALARME D’AIDE Inspiratoire Insuffisante SE Declenche SI UNE Alarme DE Fuite Importante SE DeclencheSI L’ALARME DE Debit Bloque SE Declenche Page Quotidien Nettoyage ET EntretienHebdomadaire Démontage du circuit respiratoire pour le nettoyage PeriodiqueMise EN Place DU Filtre Filtre a AIREntretien Strategie DE Depannage Problème Cause possible SolutionPage Glossaire Page Caracteristiques Cm H2O, si cette valeur est inférieure Pression Max Informations concernant l’environnement 101 102 103 104 Produit Durée de la Garantie Garantie Limitee106 Index 108

AutoSet CS 2 specifications

ResMed AutoSet CS 2 is a state-of-the-art device designed for individuals suffering from complex sleep apnea and central sleep apnea. This advanced treatment solution leverages innovation and cutting-edge technology to provide optimal comfort and effective therapy during sleep, ultimately helping users achieve a better quality of life.

One of the standout features of the AutoSet CS 2 is its sophisticated auto-adjusting pressure capabilities. The device automatically detects and responds to the patient's breathing patterns throughout the night, adjusting the pressure levels in real time to ensure that airway obstructions are effectively managed. This technology helps prevent both hypopneas and apneas, providing a seamless therapy experience.

The device is equipped with ResMed's proprietary Easy-Breathe technology, which allows for smooth pressure changes that mimic the user's natural breathing cycle. This feature enhances user comfort, making it easier for individuals to adapt to CPAP therapy and continue using the device consistently over time.

Another remarkable characteristic of the AutoSet CS 2 is its integrated wireless connectivity. This connectivity facilitates remote monitoring and data sharing with healthcare professionals, enabling more effective management of treatment progress. By analyzing sleep data, providers can make informed adjustments to therapy, ensuring that the patient receives the best possible care.

The AutoSet CS 2 also includes a user-friendly interface with a high-resolution color display, making it easy for users to navigate menus and access vital information about their sleep patterns and therapy effectiveness. With its compact design, the device is portable and can easily be used at home or while traveling.

In terms of comfort, the AutoSet CS 2 features a quiet operation, enabling a peaceful sleep environment. It is compatible with various masks, providing flexibility for users to find the best fit for their personal comfort preferences.

Overall, the ResMed AutoSet CS 2 is a leading choice for individuals with complex sleep apnea. With its combination of advanced features, user-centric design, and state-of-the-art technology, it empowers users to take control of their sleep and improve their overall health and well-being.
Top Page Image Contents