ResMed AutoSet CS 2 user manual Mask, Learn Circuit

Page 30

SETTINGS MENU

You will only see the options relevant to your therapy. In CPAP (Continuous Positive Airway Pressure) mode, the clinician sets a pressure that will be constant throughout treatment. In ASV-CS mode, AUTOSET CS2 continually measures your breathing and regulates the air pressure accordingly.

MASK

Select the type of mask that you will be using (you will only need to adjust this if you have more than one mask). The following table shows the setting that should be selected for each mask type. If your mask type is not mentioned below, please contact your clinician. Not all mask types can be used with the AUTOSET CS2.

Option in Settings menu

Use setting with:

 

 

Vista

VISTA™

 

 

Ultra

ULTRA MIRAGE™

 

 

Full Face

MIRAGE™ FULL FACE MASK SERIES II

 

ULTRA MIRAGE FULL FACE MASK

 

 

Activa

ACTIVA™

 

 

Papillon

Papillon

Table 2: Selecting mask options in the Settings menu

LEARN CIRCUIT

The Air Circuit Learn function takes approximately 20 seconds to run. It allows the unit to ’learn’ what pressure it needs to build in to its calculations, based on the components in the system. Select LEARN CIRCUIT every time you add or remove a component (eg mask, humidifier) or move to a significantly different altitude.

To run this function:

1.Set up the entire AUTOSET CS2 system (flow generator, mask, humidifier etc) as you wish to use it.

2.Make sure that the mask is unobstructed so air can flow from the mask to the flow generator.

3.Turn on the AUTOSET CS2 at the power switch.

4.Move through the menus until you reach LEARN CIRCUIT and select ’yes’ by pressing the Left key.

5.A message will remind you to check that the airflow from the mask is clear. Select ’start’ with the Left key.

6.A progress screen is displayed while the Air Circuit Learn function is running.

LEARNING CIRCUIT

26

Page 29 Page 31
Image 30
Page 29 Page 31
Contents AutoSet CS EUR AutoSet CS Page Autoset CS Page Table of Contents Cleaning and Maintenance USER/OWNER Responsibility IntroductionAutoset CS2 Medical InformationPage Quick Setup Guide Page Autoset CS2 System Autoset CS2 ComponentsConnect this end Connect the power cord Assembling the Autoset CS2 SystemConnect air tubing Humidifiers Attach the mask to the air tubingConnecting a Humidifier Humidaire Perform the Air Circuit Learn function see Reslink ANTI-BACTERIAL FilterUsing DC Power to RUN the Autoset CS2 Inserting anti-bacterial filtersUsing Supplemental Oxygen Oxygen tube attached to Mirage FFMS2 and Ultra Mirage masksPage Starting Treatment Using the Autoset CS2Standby Mode Stopping TreatmentSTART/STOP KEY Control Panel FunctionsLCD Screen UP/DOWN KEYLeft KEY Green Adjusting SettingsAlarm Leds and Alarm Mute Right KEY REDYou wish to change the sound level for the alarms ExampleMenus Navigating the Patient menuMask Learn CircuitSmartstop Leak AlertSound Level Usage Mask FITAverage Pressure Smart DataTreatment Screens ApneaPage Alarms If a LOW Pressure Alarm SoundsTriggered by If a High Leak Alarm Sounds If a Power Fail Alarm SoundsIf a High Pressure Alarm Sounds Will Clear WhenIf AN Insufficient Pressure Support Alarm Sounds If a Flow Blocked Alarm SoundsPage Cleaning and Maintenance DailyWeekly Periodically AIR FilterServicing Fitting the FilterPage Troubleshooting Problem Possible cause SolutionPage Glossary Page Technical Specifications Leak exceeds 30 L/min for more than 20 seconds Max Pressure Environmental information English Next Recommended separation distance Separation distance according to frequency of transmitter Limited Warranty Product Warranty PeriodPage Index Page Manuel Utilisateur Page Sommaire Nettoyage ET Entretien Responsabilite DE L’UTILISATEUR/DU Proprietaire Informations MedicalesPrecautions AvertissementsGuide D’INSTALLATION Rapide Page Autoset CS2 Composants DE L’AUTOSET CS2Raccordez cette extrémité Avertissement Montage DE L’AUTOSET CS2Raccordez le circuit respiratoire Humidificateurs Montage de l’AutoSet CS2Voir « Début du traitement » De l’AutoSet CS2 Avertissement Filtre Antibacterien Utilisation D’UNE Alimentation CC Avec L’AUTOSET CS2 Mise en place des filtres antibactériensAvertissements Utilisation D’OXYGENE SupplementairePage Debut DU Traitement Mode D’ATTENTEUtilisation DE L’AUTOSET CS2 Arret DU TraitementEcran LCD Touche DE Deplacement Vers LE HAUT/BASFonctions DU Panneau DE Controle Touche MARCHE/ARRETTouche DE Gauche Verte Temoins D’ALARME ET Desactivation DE L’ALARMEModification DES Reglages Touche DE Droite RougeVous souhaitez modifier le niveau du son pour les alarmes ExempleNavigation dans le menu Patient Masque IDENT. CircuitAlarme Fuite AI FaibleAjustement DU Masque Pression MoyenneUtilisation Ecrans DE Traitement RETRO-ECLLangue Remarquecibl nest pas un paramètre utilisé en mode Cpap LES Alarmes Declenchee LorsqueSI UNE Alarme DE Pression Elevee SE Declenche SI UNE Alarme DE Pression Basse SE DeclencheSI UNE Alarme DE Panne DE Courant SE Declenche ’ARRETE LorsqueSI UNE Alarme DE Fuite Importante SE Declenche SI L’ALARME D’AIDE Inspiratoire Insuffisante SE DeclencheSI L’ALARME DE Debit Bloque SE Declenche Page Nettoyage ET Entretien QuotidienHebdomadaire Periodique Démontage du circuit respiratoire pour le nettoyageFiltre a AIR Mise EN Place DU FiltreEntretien Problème Cause possible Solution Strategie DE DepannagePage Glossaire Page Caracteristiques Cm H2O, si cette valeur est inférieure Pression Max Informations concernant l’environnement 101 102 103 104 Garantie Limitee Produit Durée de la Garantie106 Index 108

AutoSet CS 2 specifications

ResMed AutoSet CS 2 is a state-of-the-art device designed for individuals suffering from complex sleep apnea and central sleep apnea. This advanced treatment solution leverages innovation and cutting-edge technology to provide optimal comfort and effective therapy during sleep, ultimately helping users achieve a better quality of life.

One of the standout features of the AutoSet CS 2 is its sophisticated auto-adjusting pressure capabilities. The device automatically detects and responds to the patient's breathing patterns throughout the night, adjusting the pressure levels in real time to ensure that airway obstructions are effectively managed. This technology helps prevent both hypopneas and apneas, providing a seamless therapy experience.

The device is equipped with ResMed's proprietary Easy-Breathe technology, which allows for smooth pressure changes that mimic the user's natural breathing cycle. This feature enhances user comfort, making it easier for individuals to adapt to CPAP therapy and continue using the device consistently over time.

Another remarkable characteristic of the AutoSet CS 2 is its integrated wireless connectivity. This connectivity facilitates remote monitoring and data sharing with healthcare professionals, enabling more effective management of treatment progress. By analyzing sleep data, providers can make informed adjustments to therapy, ensuring that the patient receives the best possible care.

The AutoSet CS 2 also includes a user-friendly interface with a high-resolution color display, making it easy for users to navigate menus and access vital information about their sleep patterns and therapy effectiveness. With its compact design, the device is portable and can easily be used at home or while traveling.

In terms of comfort, the AutoSet CS 2 features a quiet operation, enabling a peaceful sleep environment. It is compatible with various masks, providing flexibility for users to find the best fit for their personal comfort preferences.

Overall, the ResMed AutoSet CS 2 is a leading choice for individuals with complex sleep apnea. With its combination of advanced features, user-centric design, and state-of-the-art technology, it empowers users to take control of their sleep and improve their overall health and well-being.
Top Page Image Contents