ResMed AutoSet CS 2 user manual Leak exceeds 30 L/min for more than 20 seconds

Page 48

•INSUFFICIENT PRESSURE SUPPORT ALARM

Is triggered if for 3 breaths in a row the maximum mask pressure achieved at inspiratory to expiratory transition is either <87.5% of the absolute mask pressure targetted at that point, or < absolute mask pressure targetted minus 1 cmH2O, whichever is the lower.

•HIGH LEAK ALARM

Leak exceeds 30 L/min for more than 20 seconds.

•FLOW BLOCKED ALARM

Flow is less than 6 L/min for more than 20 seconds.

IEC 601-1CLASSIFICATIONS

Class II, Type CF

Class II medical electrical equipment provides protection against electric shock either by double insulation or reinforced insulation and does not require a protective earth.

Table 3: Displayed values

Value

Range

Accuracy

Display

Resolution

 

 

 

 

 

 

 

Proximal cuff

 

 

 

 

 

 

 

Pressure

-3 to 40 cmH2O

0.5 cmH2O

0.1 cmH2O

 

 

 

 

Mass flow sensor

 

 

 

 

 

 

 

Leak

0–99 litres per

+/- 12 litres per

1 litre per breath

 

minute

minute

 

 

 

 

 

Respiratory rate

8–30 breaths per

+/- 10%

1 breath per

 

minute

 

minute

 

 

 

 

Tidal volume

0–4500 millilitres

+/- 10%

1 millilitre

 

 

 

 

Minute ventilation

0–40 litres per

+/- 10%

0.1 litres per

 

minute

 

minute

 

 

 

 

Target MV

0–40 litres per

+/- 10%

0.1 litres per

 

minute

 

minute

 

 

 

 

Table 4: Maximum low impedance flow at stated pressures

Pressure

Flow (L/min)

(cmH2O)

 

 

 

4.2217

8.6218

13.0219

44

Page 47 Page 49
Image 48
Page 47 Page 49
Contents AutoSet CS EUR AutoSet CS Page Autoset CS Page Table of Contents Cleaning and Maintenance Introduction Autoset CS2USER/OWNER Responsibility Medical InformationPage Quick Setup Guide Page Autoset CS2 System Autoset CS2 ComponentsConnect this end Connect the power cord Assembling the Autoset CS2 SystemConnect air tubing Humidifiers Attach the mask to the air tubingConnecting a Humidifier Humidaire Perform the Air Circuit Learn function see Reslink ANTI-BACTERIAL FilterUsing DC Power to RUN the Autoset CS2 Inserting anti-bacterial filtersUsing Supplemental Oxygen Oxygen tube attached to Mirage FFMS2 and Ultra Mirage masksPage Using the Autoset CS2 Standby ModeStarting Treatment Stopping TreatmentControl Panel Functions LCD ScreenSTART/STOP KEY UP/DOWN KEYAdjusting Settings Alarm Leds and Alarm MuteLeft KEY Green Right KEY REDYou wish to change the sound level for the alarms ExampleMenus Navigating the Patient menuMask Learn CircuitSmartstop Leak AlertSound Level Mask FIT Average PressureUsage Smart DataTreatment Screens ApneaPage Alarms If a LOW Pressure Alarm SoundsTriggered by If a Power Fail Alarm Sounds If a High Pressure Alarm SoundsIf a High Leak Alarm Sounds Will Clear WhenIf AN Insufficient Pressure Support Alarm Sounds If a Flow Blocked Alarm SoundsPage Cleaning and Maintenance DailyWeekly Periodically AIR FilterServicing Fitting the FilterPage Troubleshooting Problem Possible cause SolutionPage Glossary Page Technical Specifications Leak exceeds 30 L/min for more than 20 seconds Max Pressure Environmental information English Next Recommended separation distance Separation distance according to frequency of transmitter Limited Warranty Product Warranty PeriodPage Index Page Manuel Utilisateur Page Sommaire Nettoyage ET Entretien Responsabilite DE L’UTILISATEUR/DU Proprietaire Informations MedicalesPrecautions AvertissementsGuide D’INSTALLATION Rapide Page Autoset CS2 Composants DE L’AUTOSET CS2Raccordez cette extrémité Avertissement Montage DE L’AUTOSET CS2Raccordez le circuit respiratoire Humidificateurs Montage de l’AutoSet CS2Voir « Début du traitement » De l’AutoSet CS2 Avertissement Filtre Antibacterien Utilisation D’UNE Alimentation CC Avec L’AUTOSET CS2 Mise en place des filtres antibactériensAvertissements Utilisation D’OXYGENE SupplementairePage Mode D’ATTENTE Utilisation DE L’AUTOSET CS2Debut DU Traitement Arret DU TraitementTouche DE Deplacement Vers LE HAUT/BAS Fonctions DU Panneau DE ControleEcran LCD Touche MARCHE/ARRETTemoins D’ALARME ET Desactivation DE L’ALARME Modification DES ReglagesTouche DE Gauche Verte Touche DE Droite RougeVous souhaitez modifier le niveau du son pour les alarmes ExempleNavigation dans le menu Patient Masque IDENT. CircuitAlarme Fuite AI FaibleAjustement DU Masque Pression MoyenneUtilisation Ecrans DE Traitement RETRO-ECLLangue Remarquecibl nest pas un paramètre utilisé en mode Cpap LES Alarmes Declenchee LorsqueSI UNE Alarme DE Pression Basse SE Declenche SI UNE Alarme DE Panne DE Courant SE DeclencheSI UNE Alarme DE Pression Elevee SE Declenche ’ARRETE LorsqueSI UNE Alarme DE Fuite Importante SE Declenche SI L’ALARME D’AIDE Inspiratoire Insuffisante SE DeclencheSI L’ALARME DE Debit Bloque SE Declenche Page Nettoyage ET Entretien QuotidienHebdomadaire Periodique Démontage du circuit respiratoire pour le nettoyageFiltre a AIR Mise EN Place DU FiltreEntretien Problème Cause possible Solution Strategie DE DepannagePage Glossaire Page Caracteristiques Cm H2O, si cette valeur est inférieure Pression Max Informations concernant l’environnement 101 102 103 104 Garantie Limitee Produit Durée de la Garantie106 Index 108

AutoSet CS 2 specifications

ResMed AutoSet CS 2 is a state-of-the-art device designed for individuals suffering from complex sleep apnea and central sleep apnea. This advanced treatment solution leverages innovation and cutting-edge technology to provide optimal comfort and effective therapy during sleep, ultimately helping users achieve a better quality of life.

One of the standout features of the AutoSet CS 2 is its sophisticated auto-adjusting pressure capabilities. The device automatically detects and responds to the patient's breathing patterns throughout the night, adjusting the pressure levels in real time to ensure that airway obstructions are effectively managed. This technology helps prevent both hypopneas and apneas, providing a seamless therapy experience.

The device is equipped with ResMed's proprietary Easy-Breathe technology, which allows for smooth pressure changes that mimic the user's natural breathing cycle. This feature enhances user comfort, making it easier for individuals to adapt to CPAP therapy and continue using the device consistently over time.

Another remarkable characteristic of the AutoSet CS 2 is its integrated wireless connectivity. This connectivity facilitates remote monitoring and data sharing with healthcare professionals, enabling more effective management of treatment progress. By analyzing sleep data, providers can make informed adjustments to therapy, ensuring that the patient receives the best possible care.

The AutoSet CS 2 also includes a user-friendly interface with a high-resolution color display, making it easy for users to navigate menus and access vital information about their sleep patterns and therapy effectiveness. With its compact design, the device is portable and can easily be used at home or while traveling.

In terms of comfort, the AutoSet CS 2 features a quiet operation, enabling a peaceful sleep environment. It is compatible with various masks, providing flexibility for users to find the best fit for their personal comfort preferences.

Overall, the ResMed AutoSet CS 2 is a leading choice for individuals with complex sleep apnea. With its combination of advanced features, user-centric design, and state-of-the-art technology, it empowers users to take control of their sleep and improve their overall health and well-being.
Top Page Image Contents