ResMed AutoSet CS 2 user manual Smartstop, Leak Alert, Sound Level

Page 31

7.When the function is complete, a screen will appear saying that the circuit has been learned successfully. The next menu item is then displayed. Commence treatment as described in “Starting Treatment” on page 21.

If there is a problem with the circuit, a screen saying ’Invalid circuit’ will be displayed instead of the progress screen. Check that all the connections between the pieces of equipment are secure. You may need to return to the previous chapter of this manual to check that you have set up the system correctly.

SMARTSTOP

Turn the SMARTSTOP function on or off. When SMARTSTOP is on, the AUTOSET CS2 will automatically turn itself off when the mask is removed.

NOTE The unit will automatically ’SmartStart’ whenever you start to breathe into the mask.

LEAK ALERT

Turn Leak Alert on or off. Leak Alert sounds an alarm when you have a high leak from your mask. You can then adjust the mask on your face to remove the leak.

If Leak Alert is turned off, an extra leak alert message will be displayed at the end of a session if high leak occurred. The message will be displayed until a key is pressed.

RAMP (CPAP MODE ONLY)

Ramp time is the length of time taken for the air pressure to build up to the maximum pressure set by your clinician. This setting allows you to increase or decrease the ramp time in 5-minute intervals.

If you find that you are still awake when the air pressure starts to build, you may wish to increase the Ramp time.

ALARMS MENU

SOUND LEVEL

You can change the sound level of the alarms in the Alarms menu. Choose low, medium (MED) or high level to suit your needs.

LOW PS

If the clinician has enabled the Insufficient Pressure Support alarm, LOW PS will show in this menu item. See “Insufficient pressure support alarm” on page 33.

RESULTS MENU

This menu has a series of screens showing information about your most recent treatment session. If enabled by your clinician the following data may be viewed:

•Mask fit

•Average Pressure

•Usage

ENGLISH

USING THE AUTOSET CS2

27

Page 30 Page 32
Image 31
Page 30 Page 32
Contents AutoSet CS EUR AutoSet CS Page Autoset CS Page Table of Contents Cleaning and Maintenance Medical Information IntroductionAutoset CS2 USER/OWNER ResponsibilityPage Quick Setup Guide Page Autoset CS2 Components Autoset CS2 SystemConnect this end Assembling the Autoset CS2 System Connect the power cordConnect air tubing Attach the mask to the air tubing HumidifiersConnecting a Humidifier Humidaire Perform the Air Circuit Learn function see ANTI-BACTERIAL Filter ReslinkInserting anti-bacterial filters Using DC Power to RUN the Autoset CS2Oxygen tube attached to Mirage FFMS2 and Ultra Mirage masks Using Supplemental OxygenPage Stopping Treatment Using the Autoset CS2Standby Mode Starting TreatmentUP/DOWN KEY Control Panel FunctionsLCD Screen START/STOP KEYRight KEY RED Adjusting SettingsAlarm Leds and Alarm Mute Left KEY GreenExample You wish to change the sound level for the alarmsNavigating the Patient menu MenusLearn Circuit MaskLeak Alert SmartstopSound Level Smart Data Mask FITAverage Pressure UsageApnea Treatment ScreensPage If a LOW Pressure Alarm Sounds AlarmsTriggered by Will Clear When If a Power Fail Alarm SoundsIf a High Pressure Alarm Sounds If a High Leak Alarm SoundsIf a Flow Blocked Alarm Sounds If AN Insufficient Pressure Support Alarm SoundsPage Daily Cleaning and MaintenanceWeekly AIR Filter PeriodicallyFitting the Filter ServicingPage Problem Possible cause Solution TroubleshootingPage Glossary Page Technical Specifications Leak exceeds 30 L/min for more than 20 seconds Max Pressure Environmental information English Next Recommended separation distance Separation distance according to frequency of transmitter Product Warranty Period Limited WarrantyPage Index Page Manuel Utilisateur Page Sommaire Nettoyage ET Entretien Informations Medicales Responsabilite DE L’UTILISATEUR/DU ProprietaireAvertissements PrecautionsGuide D’INSTALLATION Rapide Page Composants DE L’AUTOSET CS2 Autoset CS2Raccordez cette extrémité Montage DE L’AUTOSET CS2 AvertissementRaccordez le circuit respiratoire Montage de l’AutoSet CS2 HumidificateursVoir « Début du traitement » De l’AutoSet CS2 Avertissement Filtre Antibacterien Mise en place des filtres antibactériens Utilisation D’UNE Alimentation CC Avec L’AUTOSET CS2Utilisation D’OXYGENE Supplementaire AvertissementsPage Arret DU Traitement Mode D’ATTENTEUtilisation DE L’AUTOSET CS2 Debut DU TraitementTouche MARCHE/ARRET Touche DE Deplacement Vers LE HAUT/BASFonctions DU Panneau DE Controle Ecran LCDTouche DE Droite Rouge Temoins D’ALARME ET Desactivation DE L’ALARMEModification DES Reglages Touche DE Gauche VerteExemple Vous souhaitez modifier le niveau du son pour les alarmesNavigation dans le menu Patient IDENT. Circuit MasqueAI Faible Alarme FuitePression Moyenne Ajustement DU MasqueUtilisation RETRO-ECL Ecrans DE TraitementLangue Remarquecibl nest pas un paramètre utilisé en mode Cpap Declenchee Lorsque LES Alarmes’ARRETE Lorsque SI UNE Alarme DE Pression Basse SE DeclencheSI UNE Alarme DE Panne DE Courant SE Declenche SI UNE Alarme DE Pression Elevee SE DeclencheSI L’ALARME D’AIDE Inspiratoire Insuffisante SE Declenche SI UNE Alarme DE Fuite Importante SE DeclencheSI L’ALARME DE Debit Bloque SE Declenche Page Quotidien Nettoyage ET EntretienHebdomadaire Démontage du circuit respiratoire pour le nettoyage PeriodiqueMise EN Place DU Filtre Filtre a AIREntretien Strategie DE Depannage Problème Cause possible SolutionPage Glossaire Page Caracteristiques Cm H2O, si cette valeur est inférieure Pression Max Informations concernant l’environnement 101 102 103 104 Produit Durée de la Garantie Garantie Limitee106 Index 108

AutoSet CS 2 specifications

ResMed AutoSet CS 2 is a state-of-the-art device designed for individuals suffering from complex sleep apnea and central sleep apnea. This advanced treatment solution leverages innovation and cutting-edge technology to provide optimal comfort and effective therapy during sleep, ultimately helping users achieve a better quality of life.

One of the standout features of the AutoSet CS 2 is its sophisticated auto-adjusting pressure capabilities. The device automatically detects and responds to the patient's breathing patterns throughout the night, adjusting the pressure levels in real time to ensure that airway obstructions are effectively managed. This technology helps prevent both hypopneas and apneas, providing a seamless therapy experience.

The device is equipped with ResMed's proprietary Easy-Breathe technology, which allows for smooth pressure changes that mimic the user's natural breathing cycle. This feature enhances user comfort, making it easier for individuals to adapt to CPAP therapy and continue using the device consistently over time.

Another remarkable characteristic of the AutoSet CS 2 is its integrated wireless connectivity. This connectivity facilitates remote monitoring and data sharing with healthcare professionals, enabling more effective management of treatment progress. By analyzing sleep data, providers can make informed adjustments to therapy, ensuring that the patient receives the best possible care.

The AutoSet CS 2 also includes a user-friendly interface with a high-resolution color display, making it easy for users to navigate menus and access vital information about their sleep patterns and therapy effectiveness. With its compact design, the device is portable and can easily be used at home or while traveling.

In terms of comfort, the AutoSet CS 2 features a quiet operation, enabling a peaceful sleep environment. It is compatible with various masks, providing flexibility for users to find the best fit for their personal comfort preferences.

Overall, the ResMed AutoSet CS 2 is a leading choice for individuals with complex sleep apnea. With its combination of advanced features, user-centric design, and state-of-the-art technology, it empowers users to take control of their sleep and improve their overall health and well-being.
Top Page Image Contents