ResMed AutoSet CS 2 user manual Periodically, AIR Filter

Page 40

CAUTION

! • Do not use bleach, chlorine-, alcohol- or aromatic-based solutions (including all scented oils), moisturising or antibacterial soaps to clean the cushion, mask, air tubing or the AUTOSET CS2. These solutions may cause hardening and reduce the life of the product.

• Do not wash or dry the mask frame at a temperature above 80oC (176oF). Exposure to higher temperatures may reduce the life of the product.

• Do not hang the air tubing and pressure sensor tube in direct sunlight as the tubing may harden over time and eventually crack.

PERIODICALLY

1.The mask and air tubing are subject to normal wear and tear. Inspect them regularly for damage.

2.Open the power cord locking clip and remove the cord. Clean the exterior of the flow generator with a damp cloth and mild detergent.

3.Inspect the air filter to check if it is blocked by dirt or contains holes. See full instructions below.

WARNING

! Beware of electric shock. Do not immerse the flow generator or power cord in water. Always unplug the flow generator before cleaning and be sure that it is dry before reconnecting.

CAUTION

! Do not attempt to open the AUTOSET CS2. There are no user serviceable parts inside. Repairs and internal servicing should only be performed by an authorised service agent.

AIR FILTER

Inspect the air filter every month and check if it is blocked by dirt or contains holes.

Air filter cover

The filter should be replaced every 6 months, or more often if the flow generator is operating in a dusty environment.

36

Page 39 Page 41
Image 40
Page 39 Page 41
Contents AutoSet CS EUR AutoSet CS Page Autoset CS Page Table of Contents Cleaning and Maintenance Introduction Autoset CS2USER/OWNER Responsibility Medical InformationPage Quick Setup Guide Page Autoset CS2 System Autoset CS2 ComponentsConnect this end Connect the power cord Assembling the Autoset CS2 SystemConnect air tubing Humidifiers Attach the mask to the air tubingConnecting a Humidifier Humidaire Perform the Air Circuit Learn function see Reslink ANTI-BACTERIAL FilterUsing DC Power to RUN the Autoset CS2 Inserting anti-bacterial filtersUsing Supplemental Oxygen Oxygen tube attached to Mirage FFMS2 and Ultra Mirage masksPage Using the Autoset CS2 Standby ModeStarting Treatment Stopping TreatmentControl Panel Functions LCD ScreenSTART/STOP KEY UP/DOWN KEYAdjusting Settings Alarm Leds and Alarm MuteLeft KEY Green Right KEY REDYou wish to change the sound level for the alarms ExampleMenus Navigating the Patient menuMask Learn CircuitLeak Alert SmartstopSound Level Mask FIT Average PressureUsage Smart DataTreatment Screens ApneaPage If a LOW Pressure Alarm Sounds AlarmsTriggered by If a Power Fail Alarm Sounds If a High Pressure Alarm SoundsIf a High Leak Alarm Sounds Will Clear WhenIf AN Insufficient Pressure Support Alarm Sounds If a Flow Blocked Alarm SoundsPage Daily Cleaning and MaintenanceWeekly Periodically AIR FilterServicing Fitting the FilterPage Troubleshooting Problem Possible cause SolutionPage Glossary Page Technical Specifications Leak exceeds 30 L/min for more than 20 seconds Max Pressure Environmental information English Next Recommended separation distance Separation distance according to frequency of transmitter Limited Warranty Product Warranty PeriodPage Index Page Manuel Utilisateur Page Sommaire Nettoyage ET Entretien Responsabilite DE L’UTILISATEUR/DU Proprietaire Informations MedicalesPrecautions AvertissementsGuide D’INSTALLATION Rapide Page Autoset CS2 Composants DE L’AUTOSET CS2Raccordez cette extrémité Avertissement Montage DE L’AUTOSET CS2Raccordez le circuit respiratoire Humidificateurs Montage de l’AutoSet CS2Voir « Début du traitement » De l’AutoSet CS2 Avertissement Filtre Antibacterien Utilisation D’UNE Alimentation CC Avec L’AUTOSET CS2 Mise en place des filtres antibactériensAvertissements Utilisation D’OXYGENE SupplementairePage Mode D’ATTENTE Utilisation DE L’AUTOSET CS2Debut DU Traitement Arret DU TraitementTouche DE Deplacement Vers LE HAUT/BAS Fonctions DU Panneau DE ControleEcran LCD Touche MARCHE/ARRETTemoins D’ALARME ET Desactivation DE L’ALARME Modification DES ReglagesTouche DE Gauche Verte Touche DE Droite RougeVous souhaitez modifier le niveau du son pour les alarmes ExempleNavigation dans le menu Patient Masque IDENT. CircuitAlarme Fuite AI FaiblePression Moyenne Ajustement DU MasqueUtilisation RETRO-ECL Ecrans DE TraitementLangue Remarquecibl nest pas un paramètre utilisé en mode Cpap LES Alarmes Declenchee LorsqueSI UNE Alarme DE Pression Basse SE Declenche SI UNE Alarme DE Panne DE Courant SE DeclencheSI UNE Alarme DE Pression Elevee SE Declenche ’ARRETE LorsqueSI L’ALARME D’AIDE Inspiratoire Insuffisante SE Declenche SI UNE Alarme DE Fuite Importante SE DeclencheSI L’ALARME DE Debit Bloque SE Declenche Page Quotidien Nettoyage ET EntretienHebdomadaire Periodique Démontage du circuit respiratoire pour le nettoyageFiltre a AIR Mise EN Place DU FiltreEntretien Problème Cause possible Solution Strategie DE DepannagePage Glossaire Page Caracteristiques Cm H2O, si cette valeur est inférieure Pression Max Informations concernant l’environnement 101 102 103 104 Garantie Limitee Produit Durée de la Garantie106 Index 108

AutoSet CS 2 specifications

ResMed AutoSet CS 2 is a state-of-the-art device designed for individuals suffering from complex sleep apnea and central sleep apnea. This advanced treatment solution leverages innovation and cutting-edge technology to provide optimal comfort and effective therapy during sleep, ultimately helping users achieve a better quality of life.

One of the standout features of the AutoSet CS 2 is its sophisticated auto-adjusting pressure capabilities. The device automatically detects and responds to the patient's breathing patterns throughout the night, adjusting the pressure levels in real time to ensure that airway obstructions are effectively managed. This technology helps prevent both hypopneas and apneas, providing a seamless therapy experience.

The device is equipped with ResMed's proprietary Easy-Breathe technology, which allows for smooth pressure changes that mimic the user's natural breathing cycle. This feature enhances user comfort, making it easier for individuals to adapt to CPAP therapy and continue using the device consistently over time.

Another remarkable characteristic of the AutoSet CS 2 is its integrated wireless connectivity. This connectivity facilitates remote monitoring and data sharing with healthcare professionals, enabling more effective management of treatment progress. By analyzing sleep data, providers can make informed adjustments to therapy, ensuring that the patient receives the best possible care.

The AutoSet CS 2 also includes a user-friendly interface with a high-resolution color display, making it easy for users to navigate menus and access vital information about their sleep patterns and therapy effectiveness. With its compact design, the device is portable and can easily be used at home or while traveling.

In terms of comfort, the AutoSet CS 2 features a quiet operation, enabling a peaceful sleep environment. It is compatible with various masks, providing flexibility for users to find the best fit for their personal comfort preferences.

Overall, the ResMed AutoSet CS 2 is a leading choice for individuals with complex sleep apnea. With its combination of advanced features, user-centric design, and state-of-the-art technology, it empowers users to take control of their sleep and improve their overall health and well-being.
Top Page Image Contents