Remington EL-7 16-inch, EL-7 14-inch, LNT-3 12-inch, LNT-3 10-inch, LNT-2 10-inch, LNT-2 8-inch

Page 12

¨

ELECTRIC CHAIN SAW

OPERATING CHAIN SAW

Continued

Log Supported On One End

1.Make first cut on underside of log (see Figure 15). Use top of guide bar to make this cut. Cut 1/3 through diam- eter of log. This cut will keep section from splintering when cut.

2.Make second cut directly above first cut. Cut down to meet first cut. This cut will keep log from pinching guide bar and chain.

2nd Cut

1st Cut

Figure 15 - Bucking Log When Log Is Supported On One End

Log Supported On Both Ends

1.Make first cut from above log (see Fig- ure 16). Cut 1/3 through diameter of log. This cut will keep section from splintering when cut.

2.Make second cut on underside of log, directly under first cut. Use top of guide bar to make this cut. Cut up to meet first cut. This will keep log from pinch- ing guide bar and chain.

1st Cut

2nd Cut

Figure 16 - Bucking Log When Log Is Supported On Both Ends

CLEANING AND MAINTENANCE

NOTICE: Below are instructions for servicing your chain saw. Any servicing not mentioned below should be done by an authorized service person.

CLEANING SAW BODY

WARNING: Unplug chain saw from power source before servic- ing. Severe injury or death could occur from electrical shock or body contact with moving chain.

WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain.

WARNING: When cleaning saw body

¥do not submerge saw in any liquids

¥do not use products that con- tain ammonia, chlorine, or abrasives

¥do not use chlorinated clean- ing solvents, carbon tetrachlo- ride, kerosene, or gasoline

Keep saw body clean. Use a soft cloth damp- ened with a mild soap and water mixture. Wipe saw body to clean.

CARE OF GUIDE BAR

Uneven bar wear causes most guide bar prob- lems. Incorrect sharpening of chain cutter and depth gauge settings often cause this. When bar wears unevenly, it widens guide bar groove (see Figure 17). This causes chain clatter and rivet popping. Saw will not cut straight. Replace guide bar if this occurs.

Inspect guide bar before sharpening chain. A worn or damaged guide bar is unsafe. A worn or damaged guide bar will damage chain. It will also make cutting harder.

Guide Bar

Groove

Guide Bar

Normal Guide Bar

Guide Bar With

 

Uneven Wear

Figure 17 - Guide Bar Cross Section Showing Uneven Bar Wear

For more information, visit www.desatech.com

12

105020

Image 12
Contents Electric Chain SAW Information Symbols Information Symbols AutoSafety Kickback Safety Devices On This SawBefore Operating Chain SAW KickbackSaw Maintenance and Kickback Safety Pushback and PULL-INChain SAW Operation Cause Of Pushback and Pull-InMaintenance and Storage of Chain SAW Chain SAW Names TermsAssembly Product IdentificationUnpacking Filling OIL Tank EdgeSAW Chain Tension Adjustment Operating Chain SAWExtension Cords Oiling Chain Cutting with the Chain SAWFelling Procedure Felling Notch Before Felling a TreeFelling Cut Bucking a LOG Limbing a TreeEntire Length Of Log On Ground Cleaning and Maintenance Cleaning SAW BodyCare of Guide BAR Log Supported On One EndNormal Guide Bar Maintenance Sharpening Your SAW ChainItems Needed to Sharpen Chain Sharpening CuttersReplacement Parts StorageFiling Cutter Depth Gauges Replacing Saw ChainTroubleshooting Observed Fault Possible Cause RemedyInstalling Shoulder Screw or E-Ring Depending On Model Illustrated Parts BreakdownLNT-2 and LNT-3 Parts List DescriptionEL-7 QTY KEY Description Keep this Warranty Industries of Canada, IncTronçonneuse Électrique Prime Description Symboles Description Symboles Tronçonneuse Électrique PrimeAvertissements Pour LA Sécurité Avant D’UTILISER LA TronçonneuseRecul Cause du reculPoussée ET Traction Entretien de la tronçonneuse et protection contre le reculCauses de la poussée et de la traction Utilisation DE LA TronçonneuseVocabulaire DE LA Tronçonneuse Entretien ET Remisage DE LA TronçonneuseDéballage MontageNomenclature DES Pièces Remplissage DU Réservoir D’HUILE Réglage DE LA Tension DE LA Chaîne Utilisation DE LA TronçonneuseProlongateurs DE Cordon Lubrification DE LA Chaîne Sciage Avec LA TronçonneuseAbattage D’UN Arbre Avant d’abattre un arbreProcédure d’abattage Sifflet d’abattage Trait d’abattageÉbranchage Tronçonnage D’UNE BilleToute la bille repose au sol Nettoyage ET Entretien Entretien DE LA LAME- GuideNettoyage DU Carter DE Tronçonneuse La bille est soutenue à une extrémitéAffûtage DE LA Chaîne Entretien normal de la lame- guideOutils nécessaires pour affûter la chaîne Affûtage des taillantsRemplacement de la chaîne RemisagePièces DE Rechange Limage des limiteurs de profondeur des taillantsDépannage Défaillance Observée Cause Possible RemèdeDétail DES Pièces Illustrées LNT-2 ET LNT-3Pièces Disponibles NON Représentées EL-7 075890L 100860-01 Information SUR LA Garantie Conserver Cette Garantie