RedMax TR2350S manual Operation

Page 14

TR2350S

8. Operation

OP1

■STARTING ENGINE

WARNING

The cutting head will start rotating upon the engine starts.

1. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start rotating upon starting of the engine.

2. Push the primer pump several times until overflown fuel flows out in the clear tube. (OP1)

3.Move the choke lever to the closed position. (OP1)

(1)primer pump

(2)choke lever

(3)close

(4)open

NOTE

1.When restarting the engine immediately after stopping it, leave the choke open.

2.Overchoking can make the engine hard to start due to excess fuel. When the engine failed to start after several attempts, open the choke and repeat pulling the rope, or remove the spark plug and dry it.

■STOPPING ENGINE (OP2)

1.Release the throttle lever and run the engine for a half minute.

2.Shift the stop switch to the "STOP" position.

IMPORTANT

•Except for an emergency, avoid stopping the engine while pulling the throttle lever.

OP2

 

 

(3)

(2)

 

(1)

(a)

 

4.Set the stop switch to the "RUN" position. Place the unit on a flat, firm place. Keep the cutting head clear of everything around it. (OP2)

(1) stop switch

(2) RUN

(3) STOP

OP4

 

.04 in

 

(1~2mm)

(1)

■ADJUSTING THROTTLE CABLE

• The normal play is 1 or 2mm when measured at the carburetor side end. Readjust with the cable adjuster as required. (OP4)

(1) cable adjuster

(b)

OP3

(a)lockout lever

(b)throttle trigger

5.Firmly grasp (a) and (b) with left hand, pull the starter knob quickly until engine fires. (OP3)

OP5

(1)

■ADJUSTING IDLING SPEED (OP5)

1. When the engine tends stop frequently at idling mode, turn the adjusting screw clockwise.

2. When the cutting head keeps rotating after releasing the trigger, turn the adjusting screw counter-clockwise.

(1) idle adjusting screw

IMPORTANT

•Avoid pulling the rope to its end or returning it by releasing the knob. Such actions can cause starter failures.

6.Move the choke lever downward to open the choke. And restart engine. (OP1)

7.Allow the engine to warm up for several minutes before starting operation.

NOTE

•Warm up the engine before adjusting the idling speed.

US-12

Page 13 Page 15
Image 14
Page 13 Page 15
Contents TR2350S Page TR2350S Contents TR2350S SpecificationsParts location Manufactured Symbols on the machineEmission Control For safe operation Starting the engine Using the productBefore use Maintenance Fuel safetyAvoid noise problem TransportDisposal Installing Handle Set upConnecting Switch Wires SE1 SE2 Installing Debris GuardFuel WarrantyFuel Gasoline RequirementsFor Your Engine LIFE, Avoid HOW to MIX Fuel Recommended Mixing Ratio Gasoline 50 OILMixing Chart Fueling the UnitOperation Trimming Grass and Weeds Adjusting the Line LengthCutting Work Line Head Usage OP6For safety reasons, do not use metalreinforced line MaintenanceMaintenance Chart MA1 Refilling Trimming Line MA1MA3 Fuel Filter Replacement Plug is a NGK BPMR7AMA2 AIR Filter MA5 MA6 MufflerDisposal MA8 Procedures to be Performed After Every 100 Hours of USEStorage MA7Optional blade usage OPT10 OPT7 OPT8 Starting the EngineCutting Method Controlling Blade ThrustOPT11 Maintenance BladeHow you can maintain the best control 22, 24-tooth blade Tooth blade Point OPT11Check Probable Causes Action Troubleshooting guideCase 1. Starting failure Mode D’EMPLOI Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOI Tables des matieresEmplacement des pieces Fiche techniqueMesures DE Lutte Contre LES Emissions Symboles utilises sur la machineEtiquettes d’avertissement sur la machine Consignes de securite Utilisation DU Produit Avant DE Faire Demarrer LE MoteurDemarrage DU Moteur Rangement TransportSécurité carburant Comment eviter les nuisances sonoresEntretien Recommandé deMise au rebut Raccordement DES Fils Electriques Installation DE LA Tete DE Coupe SE3Assemblage Mise EN Place DE LA PoigneeTypes DE Carburants Requis CarburantCarburant Tableau DE Melange 50 ’ANNULATION DE LA Garantie DU Moteur a DeuxRemplissage DU Reservoir Eviter Pour Prolonger LA Duree DE VIE DU MoteurFR-12 Arret DU Moteur OP3 FonctionnementOP1 Mise EN Marche DU Moteur Reglage Câble D’ACCÉLÉRATEURReglage DE LA Longeur DU FIL DE Coupe OP6 Travail DE Coupe Utilisation DE LA Tete a FILCoupe DE Gazon OU D’HERBES Tableau D’ENTRETIEN MA1 Remplacement DU FIL DE Coupe MA1Entretien MA3 Filtre a Carburant SilencieuxMA2 Filtre a AIR Bougie D’ALLUMAGE MA5 MA6Cylindre Ouïe d’entrée d’air de refroidissement arrière RangementMise au rebut Mise EN Place DE LA Lame Utilisation de la lame optionnelleChoisir LA Lame Equilibrage DE LA MachineFonctionnement OPT7 OPT8 OPT9Methode DE Coupe Controle DES Coups DE ReculComment conserver le meilleur contrôle de la machine Entretien LameGuide de localisation des pannes Verification Causes Probables ActionPage Desbrozador Contenido Advertencias Contenidas EN EL ManualTR2301S Situación de las piezasEspecificaciohes Control DE Emisiones Etiqueta de advertencia en la máquinaSímbolos presentes en la máquina Instrucciones de seguridad Antes DE Arrancar LA Máquina Arranque DEL MotorTransporte Cómo evitar problemas de ruidoUSO DEL Producto Seguridad en el uso del combusibleMantenimiento Para la protección contra las vibracionesEliminación Montaje Requerimientos de la Gasolina CombustibleCombustible Preste atención en la agitación Anulará Lagarantía DEL Motor DE DOS Tiempos RedMaxCuadro DE Mezcla Abastecimiento DE LA UnidadVacíe del carburador el combustible compuesto Cómo Parar EL Motor OP2 UsoOP1 Arranque DEL Motor Ajuste Cable DEL AceleradorAjuste DE LA Longitud DE LA Línea OP6 Trabajo DE Corte USO DEL Cabezal CortadorDesbroce DE Hierbas Y Maleza MA1 Rellenado DE LA Línea DE Desbroce MA1 MantenimientoTabla DE Mantenimiento MA3 Filtro DE Combustible Filtro DE AireMA2 SilenciadorMA8 Procedimientos a Realizar Cada 100 Horas DE USO AlmacenamientoEliminación Cilindro Toma de aire de refrigeración posteriorElija LA Hoja Uso de hoja opcionalPAR Torsor Monte LA HojaControl DEL Contragolpe DE LA Hoja Método DE CorteUSO Qué causa el contragolpeMantenimiento Hoja Cómo se puede reducir la posibilidad de contragolpe?Cuál es la mejor forma de mantener el control Hoja de 22 y 24 dientes Hoja de 8 dientes Hoja de 4 dientes13. Guía de localización y solución de problemas Comprobar Posibles Causas AcciónPage Nota Parts listRemarque Drive Unit TR2350S S/N 90200101 and up Key# Part Number Description Qty Optional Blade & AccessoriesPart Number Description Qty Engine Unit TR2350S S/N 90200101 and up Cylinder Zenoah AMERICA, INC

TR2350S specifications

The RedMax TR2350S is a high-performance trimmer designed for both professional landscapers and homeowners who seek efficiency and reliability in their gardening tools. This robust machine showcases the perfect combination of power and versatility, making it an indispensable asset in any landscaping arsenal.

One of the standout features of the TR2350S is its powerful 23.6cc engine, which delivers exceptional performance while ensuring fuel efficiency. The engine is designed with advanced technologies to minimize emissions, aligning with modern environmental standards while maintaining robust power output. This ensures that users can tackle even the toughest trimming tasks without compromising on performance or contributing to pollution.

The TR2350S also features an innovative Easy Start system, which significantly reduces the effort required to start the engine. This user-friendly technology allows for a hassle-free experience, especially important for professionals who need to start up quickly and efficiently throughout their workday.

The trimmer’s ergonomic design enhances comfort during extended periods of use. It features a curved shaft that is not only lightweight but also well-balanced, reducing operator fatigue. The soft-grip handles provide additional comfort and control, allowing users to maneuver the trimmer easily around various landscaping obstacles.

Another notable aspect of the RedMax TR2350S is its dual-line cutting system, which offers a clean and efficient cut. The trimmer comes equipped with a bump feed head, ensuring that the cutting line is automatically released with a simple tap on the ground. This feature allows users to keep working without the need to stop and adjust the line manually.

Safety is also a priority in the design of the TR2350S. The unit incorporates various safety features, including a guard that helps protect the operator from debris and an easy-to-access throttle control that keeps the user in command of the trimmer’s performance.

In conclusion, the RedMax TR2350S is a versatile, powerful, and user-friendly trimmer that caters to both professionals and homeowners. Its innovative technologies, comfort-enhancing design, and safety features make it a leading choice for those looking to efficiently maintain their outdoor spaces. With the TR2350S, users can expect reliability and performance that meets the demands of any trimming job.
Top Page Image Contents