Makita DCS 7901, DCS6401, DCS 7300, DCS 6400, DCS 7900, DCS 7301 manual Tightening the saw chain

Page 19

Pullthe chain (6) around the sprocket nose (8) of the guide bar in the direction of the arrow.

Guide the chain over the chain catch (9).

Pull the guide bar as shown by the arrow to take the slack out of the chain, so that it comes up to the bottomedge of the guide bar (10).

Line up the holes in the sprocket guard (3) with the bolts (11).

Turnthe chaintensioningscrew (HI13) untilthe chaintensioning bolt (12) is aligned with the hole in the guide bar.

Replace the sprocket guard.

Manually tighten the retaining nuts (H12).

Tightening the saw chain

Slightly liftthe end of the guide bar and turn the chain adjusting screw (13)to the right (clockwise) until the chain rests against the bottom side of the guide bar.

While still holding up the tip of the guide bar, tighten the retaining nuts (2) with the universal wrench.

NOTE:

Before tightening the chain, loosen the two nuts (2) slightly.

19

Image 19

Contents Manuel d’emploi et de securite DCS 6400,6401,7300,7301,7900,7901 Contents Page Additional safety precautions Safety precautions for chain saw operatorsWARNlNGf Physical Condition Ansi B175.1-2000Compliance with Ansi -StandardsTransporting the chain saw Use of the sawChain saw operating instructions Cutting instructions Working conditionsReactiveforces duringthe cut, includingkickback KickbackMost common reactive forces are Kickback Pushback Pull-in Object Saw chain cutter sharpnessTo avoid kickback Speed of contact at which the cutter contactsFelling PushbackTo avoid pushback To avoid pull-inFirst Cut Then, determine the placement of the felling notchFelling instructions Noise of your engine may drown any warning callSectioning Method Plunge-Cut MethodBegin the felling cut slighty higher than the felling Bucking LimbingMaintaining and storing the saw Maintenance and RepairAttempt any maintenance or repair work not de Cross cut By your Makita service shop only Muffler with spark arrester screen Denomination of components Identification plateTechnical data Mounting the guide bar and saw chain Putting Into OperationTightening the saw chain Releasing the chain brake Checking the chain tensionGasoline 50l 40l FuelRefuelling GuideEngine must be switched off Adjusting the chain lubricationChecking the chain lubrication Stopping the engine Starting the engineCold-starting Warm startingWorking in winter Adjusting the carburetorSharpening the saw chain 025 65 mm MinFile Files and how to work with themCleaning the brake band and sprocket interior Replacing the saw chain Cleaning the guide barReplacing the suction head Cleaning the air filter Checking the ignition spark CAREFUL1Injury hazard! The return spring can pop out Replacing the starter cable Replacing the return springReplacing the return spring Replacinglcleaning the spark arrester screen Mounting the fan housingService, spare parts and guarantee Instructions for periodic maintenanceCause GuaranteeSpare parts Malfunction System ObservationDCS 7300,7301 Extract from the spare parts listDCS 7900,7901 Page DCS 6400,6401,7300,7301 , 7900,7901 Additionnels Mesures de securite supplementaires Condition physique Porter le casque, les lunettes et acoustiques de protection Utilisation de la tronGonneuseTransport de la tronqonneuse Demarrage Ravitaillementen carburantInstructionsde ravitaillement @ @ ’huile ou de graisse Instructions de coupeChoc de recul Kickback IA-ALes limiteurs de profondeurs AffQtage des plaquettes de coupe de la ChalnePour eviter le choc de recul Laforce de choc derecul est proportionnelleaI’impactAbattage Le reculPour eviter le recul Pour eviter la tractionInstructions d’abattage Methode de coupe en plongee Methode de sectionnementDebitage EbranchageEntretien et stockage de la tronqonneuse Entretien et reparationCouDe transversale Silencieux avec pare-etincelles Designation des piecesCaracteristiques techniques Montage du guide et de la chaine de sciage Mise EN RouteTendre la chaine de sciage Liberer le frein a main ContrBle de la tension de la chaineFrein de chaine Enclencher le frein de chaine bloquerMelange carburant CarburantsHuile de chaine de sciage Remarque importante pour les huiles de chaine de sciage bio Remplissage des reservoirsEffectuer que si le moteur est arrete! Stop Verifier le graissage de la chaineReglage du graissage de la chaine0 RemarqueVerifier le frein de chaine Demarrer le moteurReglage du carburateur Affirtage de la chaine de sciage Mincll. .ll~.,ralLime et guidage de la lime Et de la roue a chaine NettoyerIinterieurde labandedefrein dechaineNettoyer le guide de la chaine Remplacement de la crepine daspirationNouvelle chaine de sciage Ne pas nettoyer le filtre a air a I’essence Nettoyage du filtre d’airVerification de I’etincelle d’allumage Remplacement de bougiePage Nettoyage de I’espace cylindre Montage du carter du ventilateurChangement I nettoyage du pare-etinceiles Aockage Indications de maintenance et d’entretien periodiquesGarantie Pieces de rechangeDCS 6400,6401 DCS 7300, 7301 DCS 7900 Extrait de la liste des pieces de rechangePage Dolmar Division Forbes Street Whitby, Ontario Canada, L I N Makita Canada Inc