Makita DCS6401, DCS 7901, DCS 7300, DCS 6400, DCS 7900, DCS 7301 manual Cleaning the air filter

Page 30

Cleaning the air filter

CAUTION: To prevent eye injury, alwaysweareye protection when cleaning the filter with compressed air1

Do not use fuel to clean the air filter.

Unhook the filter hood clips (1) with the combination tool and remove the filter hood (2).

Pull out the choke (3) to prevent dirt particles from getting into the carburetor.

Unhook the air filter retainer (4) by pressing in the direction shown by the arrow.

Pull the air filter (5) up and out.

IMPORTANT: Cover the intake opening with a clean cloth to prevent dirt particles from getting into the carburetor.

Choosing the right filter: The fleece filter is for use in dry or dusty conditions, The nylon filter is for use in damp conditions.

Pry apart the top and bottom of the air filter as shown in Figure.

Cleaning the fleece filter: Carefully tap out dust or carefully blow out dustfrom the insidewith compressedair. Do not brush the fleece, as this will force dirt particles into the fabric. If the filter is very dirty, it can be washed in lukewarm water with regular dishwashingdetergent. Note that the fleece filter does not needto be cleaned until there is a noticeable loss of power. If cleaning the filter does not bring an improvement in performance, it is time to replace it.

Cleaning the nylonfilter: Usea soft brushor blowout dirt from the insidewith compressedair. If the filter is very dirty, it can be washed in lukewarm water with regular dishwashing deter- gent. Clean frequently (several times a day) when working in very dusty or dirty conditions. Full engine power is possible only with a clean air filter!

Let the air filter dry completely.

Put the top and bottom sections back together.

Before assemblingtheairfilter, checkthechokeflapforany dirt particles. If there are any, remove them with a brush.

CAUTION: If the air filter becomes damaged, replace im- mediately! Pieces of cloth or large dirt particles can de- stroy the enginel

Put in the air filter (5)and press down the air filter retainer (4) evenly with thumb and forefinger until it clicks.

Push in the choke (3) and push the throttle all the way in to deactivate the half-throttle lock.

Put on the filter hood (2) and hook in the clips (I).

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Manuel d’emploi et de securite DCS 6400,6401,7300,7301,7900,7901 Contents Page Safety precautions for chain saw operators Additional safety precautionsWARNlNGf Ansi B175.1-2000Compliance with Ansi -Standards Physical ConditionUse of the saw Transporting the chain sawChain saw operating instructions Working conditions Cutting instructionsKickback Reactiveforces duringthe cut, includingkickbackMost common reactive forces are Kickback Pushback Pull-in Speed of contact at which the cutter contacts Saw chain cutter sharpnessTo avoid kickback ObjectTo avoid pull-in PushbackTo avoid pushback FellingNoise of your engine may drown any warning call Then, determine the placement of the felling notchFelling instructions First CutPlunge-Cut Method Sectioning MethodBegin the felling cut slighty higher than the felling Limbing BuckingCross cut By your Makita service shop only Maintenance and RepairAttempt any maintenance or repair work not de Maintaining and storing the sawDenomination of components Identification plate Muffler with spark arrester screenTechnical data Putting Into Operation Mounting the guide bar and saw chainTightening the saw chain Checking the chain tension Releasing the chain brakeFuel Gasoline 50l 40lGuide RefuellingAdjusting the chain lubrication Engine must be switched offChecking the chain lubrication Warm starting Starting the engineCold-starting Stopping the engineAdjusting the carburetor Working in winter025 65 mm Min Sharpening the saw chainFiles and how to work with them FileCleaning the brake band and sprocket interior Cleaning the guide bar Replacing the saw chainReplacing the suction head Cleaning the air filter Checking the ignition spark Replacing the starter cable Replacing the return spring CAREFUL1Injury hazard! The return spring can pop outReplacing the return spring Mounting the fan housing Replacinglcleaning the spark arrester screenInstructions for periodic maintenance Service, spare parts and guaranteeMalfunction System Observation GuaranteeSpare parts CauseExtract from the spare parts list DCS 7300,7301DCS 7900,7901 Page DCS 6400,6401,7300,7301 , 7900,7901 Additionnels Mesures de securite supplementaires Condition physique Utilisation de la tronGonneuse Porter le casque, les lunettes et acoustiques de protectionTransport de la tronqonneuse Ravitaillementen carburant DemarrageInstructionsde ravitaillement @ @ Instructions de coupe ’huile ou de graisseIA-A Choc de recul KickbackLaforce de choc derecul est proportionnelleaI’impact AffQtage des plaquettes de coupe de la ChalnePour eviter le choc de recul Les limiteurs de profondeursPour eviter la traction Le reculPour eviter le recul AbattageInstructions d’abattage Methode de sectionnement Methode de coupe en plongeeEbranchage DebitageEntretien et reparation Entretien et stockage de la tronqonneuseCouDe transversale Designation des pieces Silencieux avec pare-etincellesCaracteristiques techniques Mise EN Route Montage du guide et de la chaine de sciageTendre la chaine de sciage Enclencher le frein de chaine bloquer ContrBle de la tension de la chaineFrein de chaine Liberer le frein a mainCarburants Melange carburantHuile de chaine de sciage Remplissage des reservoirs Remarque importante pour les huiles de chaine de sciage bioRemarque Verifier le graissage de la chaineReglage du graissage de la chaine0 Effectuer que si le moteur est arrete! StopDemarrer le moteur Verifier le frein de chaineReglage du carburateur Mincll. .ll~.,ral Affirtage de la chaine de sciageLime et guidage de la lime NettoyerIinterieurde labandedefrein dechaine Et de la roue a chaineRemplacement de la crepine daspiration Nettoyer le guide de la chaineNouvelle chaine de sciage Nettoyage du filtre d’air Ne pas nettoyer le filtre a air a I’essenceRemplacement de bougie Verification de I’etincelle d’allumagePage Montage du carter du ventilateur Nettoyage de I’espace cylindreChangement I nettoyage du pare-etinceiles Indications de maintenance et d’entretien periodiques AockagePieces de rechange GarantieExtrait de la liste des pieces de rechange DCS 6400,6401 DCS 7300, 7301 DCS 7900Page Makita Canada Inc Dolmar Division Forbes Street Whitby, Ontario Canada, L I N

DCS 7301, DCS 7900, DCS 6400, DCS 7300, DCS 7901 specifications

Makita, a leading manufacturer of power tools, has a robust lineup of professional-grade chainsaws, including the DCS 7900, DCS 7901, DCS 7300, DCS 7301, and DCS 6401 models. Each chainsaw is designed with advanced technology to meet the demanding needs of forestry and construction professionals.

The Makita DCS 7900 is a powerful chainsaw equipped with a 79cc engine that delivers high cutting performance. It features a lightweight design combined with a powerful engine, allowing for maximum maneuverability. The saw's decompression valve ensures easy starting, while the adjustable chain oiler provides lubrication tailored to various cutting conditions. Its anti-vibration technology minimizes user fatigue during prolonged use, making it an excellent choice for professionals.

The DCS 7901 is an enhanced version of the DCS 7900, featuring an electronically controlled ignition system that optimizes fuel combustion for increased efficiency and lower emissions. This model maintains the same robust power but with improved fuel economy, making it an environmentally friendly option without sacrificing performance. The DCS 7901 also includes a heavy-duty air filter system, ensuring longer operation times by extending the life of the engine.

The DCS 7300 and DCS 7301 models are mid-range chainsaws that deliver exceptional power and versatility. The DCS 7300 features a 73cc engine, offering a perfect balance of weight and power, ideal for both felling and limbing. The DCS 7301 shares similar specifications with the DCS 7300 but includes additional features such as a tool-less chain adjustment system and a larger fuel tank for increased run time. Both models come with advanced anti-vibration technologies that ensure smooth operation.

Finally, the Makita DCS 6401 is a compact yet powerful chainsaw designed for users who require maneuverability without compromising on power. Equipped with a 64cc engine, this chainsaw is suitable for a variety of cutting tasks. It features a lightweight construction, making it ideal for prolonged use in tight spaces. The DCS 6401 also has a high-performance air filtration system, which increases engine life and efficiency.

In summary, all Makita chainsaws in this lineup are designed with user comfort and efficiency in mind. With powerful engines, advanced technology, and robust features, the DCS 7900, DCS 7901, DCS 7300, DCS 7301, and DCS 6401 ensure reliability and performance for professional users in demanding environments.
Top Page Image Contents