Makita DCS 6400, DCS6401 manual Montage du carter du ventilateur, Nettoyage de I’espace cylindre

Page 69

Montage du carter du ventilateur

Poser le carter du ventilateur (13).

Presser les vis (14) dans les trous de reception.

Lever legerement le carter du moteur (15), accrocher I’attache

(16)au carter du ventilateur avec le pouce (voir fleche).

Aligner le carter du ventilateur, presser legerement contre la tronGonneuse en tirant sur la poignee de lancement jusqu’a ce que le dispositif de lancement s’enclenche.

Bien serrer les vis (14).

Nettoyage de I’espace cylindre

Enlever le capot du filtre et le filtre a air. Retirer la cosse et devisser la bougie.

Enfoncer la soupape de demarrage et desserrer le frein de chaine.

Mettre le passe-cable avec le cable d’allumage sur le cBte. Devisser les deux vis de derriere du capot.

Devisser la vis de I’axe du pare-main et enlever la douille. Soulever et enlever le capot du guide-flexible d’aspiration.

IMPORTANT : Remettre le filtre A aire en place et le fixer, revisser la bougie et la serrer A la main. Poser la cosse et retirer la soupape de demarrage.

Enlever le capot du ventilateur et retirer le deflecteur de ventilateur.

ATTENTION: En cas d’utilisation d’air comprime pour le nettoyage, utiliser imperativement des lunettes de protection pour eviter toute blessure au niveau des yeux I

Toute la zone degarnie (17) peut 6tre nettoyeeavec une brosse et de I’air comprime.

Pour nettoyer les ailettes du cylindre, il est possible d’utiliser une brosse a bouteille.

Changement I nettoyage du pare-etinceiles

IIfaut verifier et nettoyer regulierement le pare-etincelles. Desserrer le vis (18) et enlever le pare-etencelles(19).

ATTENTION: N’utilisez pas d’objets coupants ou pointus pour nettoyer le pare-etincelles car vous pourriez endommager ou deformer les fils du pare-etincelles.

Remontez le pare-etincelles et serrez la vis.

I

Page 68 Page 70
Image 69
Page 68 Page 70
Contents Manuel d’emploi et de securite DCS 6400,6401,7300,7301,7900,7901 Contents Page Safety precautions for chain saw operators Additional safety precautionsWARNlNGf Physical Condition Ansi B175.1-2000Compliance with Ansi -StandardsTransporting the chain saw Use of the sawChain saw operating instructions Cutting instructions Working conditionsKickback Reactiveforces duringthe cut, includingkickbackMost common reactive forces are Kickback Pushback Pull-in To avoid kickback Saw chain cutter sharpnessSpeed of contact at which the cutter contacts ObjectTo avoid pushback PushbackTo avoid pull-in FellingFelling instructions Then, determine the placement of the felling notchNoise of your engine may drown any warning call First CutPlunge-Cut Method Sectioning MethodBegin the felling cut slighty higher than the felling Bucking LimbingAttempt any maintenance or repair work not de Maintenance and RepairCross cut By your Makita service shop only Maintaining and storing the sawMuffler with spark arrester screen Denomination of components Identification plateTechnical data Mounting the guide bar and saw chain Putting Into OperationTightening the saw chain Releasing the chain brake Checking the chain tensionGasoline 50l 40l FuelRefuelling GuideAdjusting the chain lubrication Engine must be switched offChecking the chain lubrication Cold-starting Starting the engineWarm starting Stopping the engineWorking in winter Adjusting the carburetorSharpening the saw chain 025 65 mm MinFile Files and how to work with themCleaning the brake band and sprocket interior Cleaning the guide bar Replacing the saw chainReplacing the suction head Cleaning the air filter Checking the ignition spark Replacing the starter cable Replacing the return spring CAREFUL1Injury hazard! The return spring can pop outReplacing the return spring Replacinglcleaning the spark arrester screen Mounting the fan housingService, spare parts and guarantee Instructions for periodic maintenanceSpare parts GuaranteeMalfunction System Observation CauseExtract from the spare parts list DCS 7300,7301DCS 7900,7901 Page DCS 6400,6401,7300,7301 , 7900,7901 Additionnels Mesures de securite supplementaires Condition physique Utilisation de la tronGonneuse Porter le casque, les lunettes et acoustiques de protectionTransport de la tronqonneuse Ravitaillementen carburant DemarrageInstructionsde ravitaillement @ @ ’huile ou de graisse Instructions de coupeChoc de recul Kickback IA-APour eviter le choc de recul AffQtage des plaquettes de coupe de la ChalneLaforce de choc derecul est proportionnelleaI’impact Les limiteurs de profondeursPour eviter le recul Le reculPour eviter la traction AbattageInstructions d’abattage Methode de coupe en plongee Methode de sectionnementDebitage EbranchageEntretien et reparation Entretien et stockage de la tronqonneuseCouDe transversale Silencieux avec pare-etincelles Designation des piecesCaracteristiques techniques Montage du guide et de la chaine de sciage Mise EN RouteTendre la chaine de sciage Frein de chaine ContrBle de la tension de la chaineEnclencher le frein de chaine bloquer Liberer le frein a mainCarburants Melange carburantHuile de chaine de sciage Remarque importante pour les huiles de chaine de sciage bio Remplissage des reservoirsReglage du graissage de la chaine0 Verifier le graissage de la chaineRemarque Effectuer que si le moteur est arrete! StopVerifier le frein de chaine Demarrer le moteurReglage du carburateur Affirtage de la chaine de sciage Mincll. .ll~.,ralLime et guidage de la lime Et de la roue a chaine NettoyerIinterieurde labandedefrein dechaineRemplacement de la crepine daspiration Nettoyer le guide de la chaineNouvelle chaine de sciage Ne pas nettoyer le filtre a air a I’essence Nettoyage du filtre d’airVerification de I’etincelle d’allumage Remplacement de bougiePage Montage du carter du ventilateur Nettoyage de I’espace cylindreChangement I nettoyage du pare-etinceiles Aockage Indications de maintenance et d’entretien periodiquesGarantie Pieces de rechangeDCS 6400,6401 DCS 7300, 7301 DCS 7900 Extrait de la liste des pieces de rechangePage Dolmar Division Forbes Street Whitby, Ontario Canada, L I N Makita Canada Inc

DCS 7301, DCS 7900, DCS 6400, DCS 7300, DCS 7901 specifications

Makita, a leading manufacturer of power tools, has a robust lineup of professional-grade chainsaws, including the DCS 7900, DCS 7901, DCS 7300, DCS 7301, and DCS 6401 models. Each chainsaw is designed with advanced technology to meet the demanding needs of forestry and construction professionals.

The Makita DCS 7900 is a powerful chainsaw equipped with a 79cc engine that delivers high cutting performance. It features a lightweight design combined with a powerful engine, allowing for maximum maneuverability. The saw's decompression valve ensures easy starting, while the adjustable chain oiler provides lubrication tailored to various cutting conditions. Its anti-vibration technology minimizes user fatigue during prolonged use, making it an excellent choice for professionals.

The DCS 7901 is an enhanced version of the DCS 7900, featuring an electronically controlled ignition system that optimizes fuel combustion for increased efficiency and lower emissions. This model maintains the same robust power but with improved fuel economy, making it an environmentally friendly option without sacrificing performance. The DCS 7901 also includes a heavy-duty air filter system, ensuring longer operation times by extending the life of the engine.

The DCS 7300 and DCS 7301 models are mid-range chainsaws that deliver exceptional power and versatility. The DCS 7300 features a 73cc engine, offering a perfect balance of weight and power, ideal for both felling and limbing. The DCS 7301 shares similar specifications with the DCS 7300 but includes additional features such as a tool-less chain adjustment system and a larger fuel tank for increased run time. Both models come with advanced anti-vibration technologies that ensure smooth operation.

Finally, the Makita DCS 6401 is a compact yet powerful chainsaw designed for users who require maneuverability without compromising on power. Equipped with a 64cc engine, this chainsaw is suitable for a variety of cutting tasks. It features a lightweight construction, making it ideal for prolonged use in tight spaces. The DCS 6401 also has a high-performance air filtration system, which increases engine life and efficiency.

In summary, all Makita chainsaws in this lineup are designed with user comfort and efficiency in mind. With powerful engines, advanced technology, and robust features, the DCS 7900, DCS 7901, DCS 7300, DCS 7301, and DCS 6401 ensure reliability and performance for professional users in demanding environments.
Top Page Image Contents