Makita DCS6401, DCS 7901, DCS 7300 manual Mise EN Route, Montage du guide et de la chaine de sciage

Page 54

I

:hl

MISE EN ROUTE

ATTENTION:

Pour tous travaux effectues sur le guide de la chaine de sciage, le moteur doit 6tre imperativement arrete et lafiche de bougie doit Ctre enlevee (voir paragraphe pour le rem- placement de la bougie) et le port de gants de protection est obligatoirel

ATTENTION:

La tronGonneuse ne peut 6tre demarree qu’apres le montage complet et le contr8le e f f e c t d l

Montage du guide et de la chaine de sciage

Utiliser la cle combinee livree avec la machine pour les travaux suivants.

Placer la tronConneuse sur un support stable et executer les operations suivantes pour le montage de la chaine de sciage et du guide de la chaine.

Desserrer le frein de chaine. Pour cela, tirer le protege-main

(1)dans le sens de la fleche. Deviser les ecrous de fixation (2).

Retirer la protection de la roue a chaine (3).

Poser la chaine de sciage (4) et la pousser contre la roue a chaine (5) dans le sens de la fleche.

Poserla chaine de sciage (6) sur le plateau (5). lntroduire avec la main droite la chaine de sciage dans la rainure de guidage superieure du guide de la chaine (7).

Attention:

Les ar6tes coupantes de la chaine de sciage doi\(ent &re dirigees dans le sens de la fleche sur la partie superieure du

54

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Manuel d’emploi et de securite DCS 6400,6401,7300,7301,7900,7901 Contents Page Safety precautions for chain saw operators Additional safety precautionsWARNlNGf Ansi B175.1-2000Compliance with Ansi -Standards Physical ConditionUse of the saw Transporting the chain sawChain saw operating instructions Working conditions Cutting instructionsKickback Reactiveforces duringthe cut, includingkickbackMost common reactive forces are Kickback Pushback Pull-in Speed of contact at which the cutter contacts Saw chain cutter sharpnessTo avoid kickback ObjectTo avoid pull-in PushbackTo avoid pushback FellingNoise of your engine may drown any warning call Then, determine the placement of the felling notchFelling instructions First CutPlunge-Cut Method Sectioning MethodBegin the felling cut slighty higher than the felling Limbing BuckingCross cut By your Makita service shop only Maintenance and RepairAttempt any maintenance or repair work not de Maintaining and storing the sawDenomination of components Identification plate Muffler with spark arrester screenTechnical data Putting Into Operation Mounting the guide bar and saw chainTightening the saw chain Checking the chain tension Releasing the chain brakeFuel Gasoline 50l 40lGuide RefuellingAdjusting the chain lubrication Engine must be switched offChecking the chain lubrication Warm starting Starting the engineCold-starting Stopping the engineAdjusting the carburetor Working in winter025 65 mm Min Sharpening the saw chainFiles and how to work with them FileCleaning the brake band and sprocket interior Cleaning the guide bar Replacing the saw chainReplacing the suction head Cleaning the air filter Checking the ignition spark Replacing the starter cable Replacing the return spring CAREFUL1Injury hazard! The return spring can pop outReplacing the return spring Mounting the fan housing Replacinglcleaning the spark arrester screenInstructions for periodic maintenance Service, spare parts and guaranteeMalfunction System Observation GuaranteeSpare parts CauseExtract from the spare parts list DCS 7300,7301DCS 7900,7901 Page DCS 6400,6401,7300,7301 , 7900,7901 Additionnels Mesures de securite supplementaires Condition physique Utilisation de la tronGonneuse Porter le casque, les lunettes et acoustiques de protectionTransport de la tronqonneuse Ravitaillementen carburant DemarrageInstructionsde ravitaillement @ @ Instructions de coupe ’huile ou de graisseIA-A Choc de recul KickbackLaforce de choc derecul est proportionnelleaI’impact AffQtage des plaquettes de coupe de la ChalnePour eviter le choc de recul Les limiteurs de profondeursPour eviter la traction Le reculPour eviter le recul AbattageInstructions d’abattage Methode de sectionnement Methode de coupe en plongeeEbranchage DebitageEntretien et reparation Entretien et stockage de la tronqonneuseCouDe transversale Designation des pieces Silencieux avec pare-etincellesCaracteristiques techniques Mise EN Route Montage du guide et de la chaine de sciageTendre la chaine de sciage Enclencher le frein de chaine bloquer ContrBle de la tension de la chaineFrein de chaine Liberer le frein a mainCarburants Melange carburantHuile de chaine de sciage Remplissage des reservoirs Remarque importante pour les huiles de chaine de sciage bioRemarque Verifier le graissage de la chaineReglage du graissage de la chaine0 Effectuer que si le moteur est arrete! StopDemarrer le moteur Verifier le frein de chaineReglage du carburateur Mincll. .ll~.,ral Affirtage de la chaine de sciageLime et guidage de la lime NettoyerIinterieurde labandedefrein dechaine Et de la roue a chaineRemplacement de la crepine daspiration Nettoyer le guide de la chaineNouvelle chaine de sciage Nettoyage du filtre d’air Ne pas nettoyer le filtre a air a I’essenceRemplacement de bougie Verification de I’etincelle d’allumagePage Montage du carter du ventilateur Nettoyage de I’espace cylindreChangement I nettoyage du pare-etinceiles Indications de maintenance et d’entretien periodiques AockagePieces de rechange GarantieExtrait de la liste des pieces de rechange DCS 6400,6401 DCS 7300, 7301 DCS 7900Page Makita Canada Inc Dolmar Division Forbes Street Whitby, Ontario Canada, L I N

DCS 7301, DCS 7900, DCS 6400, DCS 7300, DCS 7901 specifications

Makita, a leading manufacturer of power tools, has a robust lineup of professional-grade chainsaws, including the DCS 7900, DCS 7901, DCS 7300, DCS 7301, and DCS 6401 models. Each chainsaw is designed with advanced technology to meet the demanding needs of forestry and construction professionals.

The Makita DCS 7900 is a powerful chainsaw equipped with a 79cc engine that delivers high cutting performance. It features a lightweight design combined with a powerful engine, allowing for maximum maneuverability. The saw's decompression valve ensures easy starting, while the adjustable chain oiler provides lubrication tailored to various cutting conditions. Its anti-vibration technology minimizes user fatigue during prolonged use, making it an excellent choice for professionals.

The DCS 7901 is an enhanced version of the DCS 7900, featuring an electronically controlled ignition system that optimizes fuel combustion for increased efficiency and lower emissions. This model maintains the same robust power but with improved fuel economy, making it an environmentally friendly option without sacrificing performance. The DCS 7901 also includes a heavy-duty air filter system, ensuring longer operation times by extending the life of the engine.

The DCS 7300 and DCS 7301 models are mid-range chainsaws that deliver exceptional power and versatility. The DCS 7300 features a 73cc engine, offering a perfect balance of weight and power, ideal for both felling and limbing. The DCS 7301 shares similar specifications with the DCS 7300 but includes additional features such as a tool-less chain adjustment system and a larger fuel tank for increased run time. Both models come with advanced anti-vibration technologies that ensure smooth operation.

Finally, the Makita DCS 6401 is a compact yet powerful chainsaw designed for users who require maneuverability without compromising on power. Equipped with a 64cc engine, this chainsaw is suitable for a variety of cutting tasks. It features a lightweight construction, making it ideal for prolonged use in tight spaces. The DCS 6401 also has a high-performance air filtration system, which increases engine life and efficiency.

In summary, all Makita chainsaws in this lineup are designed with user comfort and efficiency in mind. With powerful engines, advanced technology, and robust features, the DCS 7900, DCS 7901, DCS 7300, DCS 7301, and DCS 6401 ensure reliability and performance for professional users in demanding environments.
Top Page Image Contents