Husky H1600 warranty No water coming out, Wand No wand attached to the Gun, Defective Gfci Plug

Page 22

PROBLEM OR CONCERN

POSSIBLE CAUSE

SOLUTION

 

 

 

No water coming out of

Gun/Hose Assembly is defective

Attach the Gun/Hose to the front of the unit with

Wand

 

no wand attached to the Gun.

 

 

Squeeze the trigger of the gun to ensure that water

 

 

comes out of the front of the Gun at a rate equal

 

 

to the Garden Hose. If no water comes out of the

 

 

Gun, remove the gun and the hose to ensure that

 

 

water flows out of the pump. If it does, the gun will

 

 

need to be replaced. Contact us at:

 

 

customerservice@huskypowerwasher.com

 

 

or order a replacement directly online at:

 

 

www.huskypowerwasher.com.

Trigger will not move

Gun Safety Lock in engaged

Release Safety Lock as instructed in Manual.

 

 

 

Unit will not start

Unit is not turned on

Press ON/OFF Switch into ON position.

Note: Unit will only start when

 

 

Loose or disconnected Plug

Reconnect Plug.

trigger is depressed.

 

 

Defective GFCI Plug

If the GFCI does not work it will need to be re-

 

Unit stops while operating

 

placed. Contact us at:

 

 

customerservice@huskypowerwasher.com

 

 

or order a replacement directly online at:

 

 

www.huskypowerwasher.com.

 

Extension Cord length or gauge

Use proper Extension Cord as instructed in section

 

incorrect

4.3.

 

Gun trigger not operating

Contact us at:

 

properly

customerservice@huskypowerwasher.com

 

 

or order a replacement directly online at:

 

 

www.huskypowerwasher.com.

 

Defective Gun

Remove the Gun and Hose assembly from the

 

 

front of the unit. Aim water stream away from

 

 

electric source and switch the unit into the ON

 

 

position. If the unit starts and water comes out

 

 

of the front, the Gun may need to be replaced.

 

 

Contact us at:

 

 

customerservice@huskypowerwasher.com

 

 

or order a replacement directly online at:

 

 

www.huskypowerwasher.com.

 

Tripped Pressure washer

Allow to cool and restart unit.

 

Thermal Switch

 

 

Defective ON/OFF Switch

Contact us at:

 

 

customerservice@huskypowerwasher.com

 

 

or order a replacement directly online at:

 

 

www.huskypowerwasher.com.

Unit will not stop when trigger

Screen filter is clogged

Clean the Screen filter as instructed in the section

is released

 

6.4.

 

Garden Hose is kinked or

Make sure the Garden Hose is laid out flat and

 

leaking water

there are no kinks in it. The hose should not be

 

 

wrapped on a storage wheel. Make sure the

 

 

faucet is open all the way and there is a full

 

 

volume of water reaching the unit.

22

Image 22
Contents Page 200 Serial NumberImportante Número de seriePág Click-N-CleanTMSPRAY NOZZLE.Click-N-CleanTM Pág Instalación fácil PágParts Drawing Diseño Piezas Parts List FigSpray Gun Click-N-CleanTMVariable Spray Lance Lista Piezas FigFOR Easy installation Instalación fácil Connect the Garden Hose to Water Page Important Safety Instructions Importantes Instrucciones DE SeguridadGuarde Estas Instrucciones Arcing parts may cause ignitionConexiones Operativas Power Supply ConnectionOperating Connections High Pressure HoseAWG Outdoor Wire GaugeExtension Cords ExtensionesInstrucciones DE USO START-UP ProcedureOperating Instructions Procedimiento DE Puesta EN MarchaBoquilla DE Pulverización Click-N-CleanTM Click-N-CleanTMSpray NozzleUSE of Cleaning Detergents Daños en la superficie que se va a pulverizarSqueeze the gun trigger and apply detergent as needed Técnicas DE Limpieza Cleaning TechniquesApplication of Detergent Aplicación DEL DetergenteFinalización DE LA Operación END of OperationMoving TrasladoMaintenance Mantenimiento Cooling System Servicing a DOUBLE- Insulated ApplianceManutención DE UN Equipo CON Doble Aislamiento Sistema DE RefrigeraciónNever use Bleach, Ammonia or Hot TroubleshootingProblem or Concern Possible Cause Solution Water in the unitFor assistance Leaking water from bottom Manifold Assembly is leakingPump housing is leaking water Email us at Or order online atNo water coming out Trigger will not move Gun Safety Lock in engagedVolume of water reaching the unit Wand No wand attached to the GunGun at a rate equal to the Garden Hose Wand is malfunctioningGun is not operating properly Wand Attaching To attach the Wand apply some moderateNo poner nunca lejía, amoniaco o agua Problema Causas Posibles SoluciónLocalización DE LAS Averías Caliente en la unidadRealice un pedido en La parte inferior de la La conexión de entrada de laCon nosotros vía e-mail en La parte inferior de la El colector pierde aguaGuera para asegurarse que fluye agua de la Hay un volumen de agua regularAgua de la pistola, retirar la pistola y la man Contacte con nosotros vía e-mail enConectar el tubo En una proporción igual a la de la mangueraDel jardín Mismo tiempo que se le da 1/4 de vuelta en elVisite Nuestro Sitio WEB Para ReGI Technical Data Datos TécnicosMax rated pressure 1400 psi Presión massima STRO, SOLUCION, Y RepuestosCard is not required to validate this warranty Limited WarrantyGarantía limitada Implied Warranties HOW to Obtain Warranty ServiceCómo Obtener EL Servicio Garantía Page Hecho EN China

H1600 specifications

The Husky H1600 is a remarkable addition to the world of 3D printing, specifically designed to cater to the needs of professionals and enthusiasts alike. With its advanced features and robust construction, the H1600 stands out in the competitive landscape of 3D printers.

One of the standout characteristics of the Husky H1600 is its impressive build volume, allowing users to create larger objects without the need for assembly. The extensive print area ensures that designers and engineers can work on complex projects with minimal constraints. This is particularly beneficial for industries such as automotive, architecture, and aerospace, where detailed prototypes are essential.

The H1600 utilizes a high-resolution Fused Deposition Modeling (FDM) technology, allowing for precise layer adhesion and outstanding surface finish. This technology ensures that the prints are durable and meet the stringent demands of functional prototypes. Additionally, the printer supports a wide range of materials, including PLA, ABS, PETG, and specialty filaments, giving users the flexibility to choose the right material for their specific application.

Equipped with a user-friendly interface, the Husky H1600 simplifies the printing process. The touchscreen display provides easy navigation through settings and options, enabling users to start, pause, or stop prints effortlessly. Furthermore, with its automated bed leveling feature, users can achieve optimal first-layer adhesion and consistently high-quality prints without the hassle of manual adjustments.

The H1600 also boasts advanced connectivity options, including USB and Wi-Fi, allowing for seamless file transfer and remote monitoring. This capability is especially valuable in collaborative environments where multiple users may need to send print jobs to the same device. Additionally, the printer’s compatibility with various slicing software ensures that users can easily prepare their designs for printing.

Safety is a top priority with the Husky H1600, featuring an enclosed build chamber that minimizes the risk of accidents and protects sensitive components from external contaminants. This design not only enhances user safety but also improves print quality by stabilizing temperature and reducing warping.

In summary, the Husky H1600 combines a generous build volume, high-resolution FDM technology, and user-friendly features, making it an excellent choice for professionals in various fields. Its versatility in material use, robust construction, and advanced connectivity options further enhance its appeal, establishing the H1600 as a reliable tool in the realm of 3D printing.