Nilfisk-ALTO 5 SB FA Before starting the cleaner, Transport and assembly, Set the brake

Page 7

NEPTUNE 5 SB FA

2.2Operating elements See fold-out page at front of these 17. Detergent metering knob

operating instructions.

18.

Pressure gauge

 

 

19.

Power ON

1.

Spray lance

20.

Castor with parking brake

2.

Cylinder lock

21.

Water supply connection

3.

Cover for control panel

22.

Tank fi ller for anti-freeze

4.

Fuel level gauge

23.

Tank fi ller for Nilfi sk-Alto

5.

Tank fi ller for fuel

 

Anti-Scale

6.

Receptacle for service crane

24.

Canister for detergent B1)

 

and lifting ring1)

25.

Tank fi ller for detergent A

7.

Top cover release

26.

Grip for top cover

8.

Service door release

27.

Cylinder lock

9.

High pressure hose

28.

Selector switch shampoo/

 

connection

 

rinsing

10.

Main switch ON/OFF - cold

29.

Low detergent indicator

 

water/hot water

30.

Coin tester

11.Display (Temperature or Codes)

12.Temperature control

13.Low fuel indicator

14.Low Nilfi sk-Alto AntiStone (Anti-Scale) indicator

15.Service interval due/expired

16.Pump oil low

3 Before starting the cleaner

3.1Transport and assembly

1.The safest way to lift the ma- chine is to use a fork-lift truck The arrows in the illustration indicate the best places to po- sition the fork.

2.It is also possible to lift the ma-

3.2Set the brake

chine by hand from the pallet. Due to the weight this work should be done by at least three persons.

CAUTION!

Do not hold the plastic tank to lift the machine as it could become detached from the frame.

The best places to hold the ma- chine are

on the handle

on the frame between the front wheels and the guide rollers.

Every fuel-burning appliance, such as pressure washers, depends upon a proper mix of fuel and air (by weight) for proper combustion. Therefore some adjustment of the

air supply to the burner may be nec- essary to take account of altitude and the resulting air pressure. This is true whether your fuel is ‘Natural gas’, Propane or Diesel.

Your Nilfisk-ALTO hot water pres- sure washer was thoroughly tested and adjusted for optimum perform- ance before it left our factory. The factory is located at approximately 120m (390 ft) above sea level, and the combustion settings are optimal for that elevation.

If your location is higher than 1200m (3900 ft) above sea level, your burner may require re-ad- justment for proper performance and best fuel economy. Contact your Dealer or Nilfisk-ALTO for assistance.

1.Before using the cleaner for the first time, check it careful- ly for any faults or damage.

2.Run the machine only when it is in perfect working condi- tion.

3.Set the brake.

4.The slope on which the high pressure cleaner is placed must not exceed more than 100 in any direction.

1) Options / model variants

5

Image 7
Contents Neptune 5 SB FA Neptune 5 SB FA Contents General Important safety instructionsSymbols used to mark instructions For your own safetyWater connection LiquidOperation Purpose TestingDescription Bypass valveTransport and assembly Before starting the cleanerSet the brake Antiscale Install Crank handle for high pressure hose reel/cord reelMachine flow L/h Pump size ml/h ˚dH Dosage Fill up fuel tank Connecting the water supplyControl / Operation Self-service mode Mode SettingDaily tasks Switching off the cleaner Options / model variants Options / model variants Applications and methods Vehicle Task Accessories Method Buildings and Equipment Task Accessories Method Below 0C 32F After using the cleanerStoring the cleaner LinesMaintenance Tank Checking the pump oil qualityChanging the pump oil Emptying the fuel oilIndications on Display TroubleshootingIndication lights on control panel Other FaultsFurther information GuaranteeUS only EU Declaration of Conformity EU Declaration of ConformityInhalt Allgemeines Wichtige SicherheitshinweiseKennzeichnung von WarnungWasseranschluss Schutzkleidung und Schutz- brille tragenBetrieb Prüfung BeschreibungElektrik Wartung und ReparaturBremse einlegen Vor der InbetriebnahmeBedienelemente Transport/AufstellungDurchfluss l/h Pumpengröße ml/h ˚dH Dosierung Kurbel für Schlauchtrommel und Kabeltrommel montierenReinigungsmitteltanks füllen Vorratsbehälter für Nilfisk-Alto AntiStone füllenWasserschlauch anschließen Brennstofftank füllenAuffangen Bedienung / BetriebElektrischer Anschluss Achtung FrostschutzmittelBetriebsart SB-Betrieb/manuellen Betrieb einstellenSchalterstellung Oder Hinweis Tägliche Kontrollen SB-BetriebSpritzpistole verriegeln Verwendung von Reinigungsmitteln Dampfbetrieb über 100CAnwendungsgebiete und Arbeitsmethoden Und hoher Druck TemperaturMechanische Einwirkungflächen Fahrzeuge Anwendung Zubehör MethodeOberflächen Bau und Industrie Anwendung Zubehör Methode OberFrostsichere Lagerung Nach der ArbeitStolpergefahr AufbewahrungWartungsarbeiten 7.2.1 Wasserfilter reinigen WartungWartungsplan Nach den ersten Alle 6 Monate Bei Wöchentlich Betriebsstunden BedarfEntleeren PumpenölkontrollePumpenölwechsel BrennstofftankAnzeigen am Display Behebung von StörungenSonstiges EG Konformitätserklärung Garantie EG- KonformitätserklärungNeptune Technical DataPage Head Quarter