Husqvarna crt51 Ground drive belt replacement, Tine replacement, Counter tine, Rotation

Page 58

5

Eng 1. Belt guard

2.Screw

3.Screw

4.Hairpin clip and retaining pin

5.Hex nut (located behind tire)

6.New tine

7.Worn tine

8.Sharp edge

9.Hairpin clip

10. Retaining pin

Figure 18

1 2

5

3

4

Figure 19

67

Figure 20

Ground drive belt replacement

a.Remove hairpin clip and retaining pin (fig. 18) from hub of left hand wheel. Pull wheel out from tiller about 1-1/2 inches.

b.Remove belt guard by removing two (2) screws, one (1) hex nut and three (3) washers so that belt guard can slide straight out away from engine (fig. 18).

c.Loosen belt guide (fig. 17-inset)

d.Remove old belt by slipping from idler pulley (fig. 17) first.

e.Place new belt in groove to transmission pulley (large pulley) and into groove of engine pulley (fig. 17). Belt must be in groove on top of idler pulley (fig. 17). Note positon of belt to guides.

f.Tighten belt guide (fig. 17 -inset)

Tine replacement

A badly worn tine causes your tiller to work harder and dig shallower. Most important, worn tines can not chop and shred organic matter as effectively nor bury it as deeply as good tines. A tine this worn (fig. 19) needs to be replaced.

To maintain the superb tilling performance fo this machine the tines should be checked for sharpness, wear and bending, particulary the tines which are next to the transmis- sion (fig. 20). If the gap between the tines exceeds 3-1/2 inches, they should be replaced or straightened as neces- sary.

New tines should be assembled as shown in figure 21. Sharpened tine edges will rotate rearward from above (fig. 21).

CAUTION!

Never tamper with the engine governor, which is factory set for proper engine speed.

Figure 21

8

9

Counter tine

rotation

Tine

3-1/2"

Tine

10

 

max.

58

Image 58
Contents CRT51 Page Preparation Maintenance and StorageTraining Schulung OperationFonctionnement FormationPréparation Entretien ET EntreposageEsp 1. Reglas DE Seguridad Tilling Forward Neutral Reverse Fast Slow Install handle Tire pressure Connect shift rodConnect clutch cable InsetMontage des Handgriffs AbbReifendruck Anschluß der SchaltstangeAnschluss des kupplungskabels Abb AusschnittMontage du guidon Pression des pneus Montage de la barre dembrayageRattacher le câble dembrayage EncartHandvat monteren FiguurBandendruk Figuur Schakelstang monterenKoppelingskabel verbinden InzetInstalación del manillar FiguraPresión de neumáticos Conexión del cable del embragueDetalle Montaggio del manubrio Collegamento del cavo della frizione Pressione dei pneumaticiMontaggio dellasta del cambio InsertoPage Ölstand im Motor Kontrollieren Check engine oil levelFill fuel tank Kraftstofftank auffüllenControleer het motoroliepeil Vérifiez le niveau dhuile du moteurRemplissage du réservoir dessence Brandstoftank vullenControllare il livello dellolio Control del nivel de aceite del motorLlene el depósito de gasolina Rifornimento di carburanteStarting the engine Tine operationZinkenbetrieb MotorstartWarnung Démarrage du moteur Mouvement des dentsTanden starten De motor startenWaarschuwing Arranque del motor ¡ADVERTENCIAUso delle lame Messa in motoAttenzione Turning Eng ReverseStopping tines and engine Outer side shieldsTilling hints Eng TillingTilling Wenden RückwärtsgangZinken und Motor abstellen Äußere SeitenabdeckungenTips zur Bodenfräsen BodenfräsenAbb Bodenfräsen Pour tourner Marche arrièreArrêt des dents et du moteur Protections latéralesQuelques conseils pour le fraisage FraisageFraisage Bochten nemen NL Achteruit rijdenDe motor en de tanden uitschakelen Buitenste schermenBewerkingstips NL BewerkenFiguur Bewerken Giro Esp Marcha atrásPare de dientes y motor TransporteEsp Laboreo Consejos para el laboreoCurve RetromarciaArresto delle lame e del motore Dischi salvapiantaConsigli di lavorazione AraturaAratura Cultivateur Eng CultivatingUnkrautbekämpfung NL WiedenFinish Engine maitenanceTransmission Wartung des MotorsEng Storage AufbewahrungRangement NL OpslaanEsp Almacenamiento RimessaggioMaintenance schedule Lubrication chartWartungsplan SchmierplanSchema dentretien Plan de graissageOnderhoudsschema NLSmeerschemaEsp Hojo de lubricación Schema manutenzione Schema di lubrificazioneGround drive belt adjustment Position handleEinstellung des Antriebsriemens Einstellen des HandgriffsWichtig Position du guidon Réglage de la courroie de transmission au solAfstellen hoofdaandrijfriem Positie hendelBelangrijk Ajuste de correa de propulsión en tierra Posición de manillar¡IMPORTANTE Messa a punto della cinghia di trasmissione Posizione del manubrioImportante Counter tine Ground drive belt replacementTine replacement RotationAuswechseln der Zinken Auswechseln des antriebsriemensAbb Zinkendrehung im Changement des dents Remplacement de la courroie de transmission au solVeu de larrière de la fraiseuse Tand vervangen Vervangen ahoofdaandrijfriemFiguur Tegengestelde Richting draaiende Tand Reemplazo de la correa de propulsión en tierra Reemplazo de dientesSostituzione delle lame Sostituzione della cinghia di trasmissioneRotazione delal lama in opposizione Soil balls up or clumps Engine misses or lacks powerEngine overheats Startet nicht oder started schwerDe aarde vormt balletjes of kluiten Le moteur chauffeMotor oververhit La terre sagglutine sur les dentsMotor sobrecalentado AvviamentoEl motor falla o tiene poca potencia Il motore perde potenzaEng Technical Data Techinische DatenEsp Especificaciones Tecnicas Localización DE AveríasPage Page Page Rev 11.10.00 TR

crt51 specifications

The Husqvarna CRT51 is a sophisticated piece of garden equipment designed for both professional landscapers and enthusiastic homeowners looking for an efficient solution for lawn care and maintenance. This robust and versatile machine excels in cutting, mulching, and maintaining grass, ensuring a well-manicured lawn with minimal effort.

One of the standout features of the CRT51 is its high-quality cutting deck. The deck is constructed robustly to withstand the rigors of regular use while providing optimal cutting performance. Its adjustable cutting height offers versatility, allowing users to customize their lawn care according to seasonal changes and personal preferences. This unique adaptability ensures a professional finish every time, regardless of the lawn type or condition.

The CRT51 is engineered with advanced technology that enhances its performance. One notable innovation is the patented blade system, which ensures clean cuts while optimizing energy efficiency. This system not only prolongs the life of the blades but also minimizes the need for frequent maintenance, making it an ideal choice for those who love spending time in their gardens rather than constantly repairing their tools.

Ergonomics is a significant focus in the design of the Husqvarna CRT51. The machine features an adjustable handle, ensuring that users of all heights can operate it comfortably. Its lightweight frame and well-placed center of gravity help in maneuverability, making navigating tight corners and small spaces effortless. This ergonomic approach contributes to reduced fatigue during longer mowing sessions, allowing users to complete their tasks with ease.

Additional features include a user-friendly control panel that enables easy adjustments to speed and cutting height. This convenience means that even novice users can operate the CRT51 efficiently, while experienced users can maximize its potential with precision settings.

Durability is a key characteristic of the CRT51. Built with high-quality materials, it is designed to withstand harsh outdoor conditions without compromising its performance. This means that users can rely on the Husqvarna CRT51 for years, making it a worthwhile investment for maintenance and care of their lawns.

In summary, the Husqvarna CRT51 stands out as an exemplary option for lawn care, combining robust cutting capabilities, advanced technology, ergonomic design, and durability. Whether for professional landscaping or home lawn maintenance, this machine delivers exceptional results, ensuring that your outdoor space remains pristine and inviting. With its impressive features and user-friendly design, the CRT51 is sure to fulfill the needs of any gardener or landscaper.