Briggs & Stratton 209443gs manual Moderate, Intermediate, Extended

Page 21

The warranty on emissions-related parts is as follows:

•Any warranted part that is not scheduled for replacement as required maintenance in the owner’s manual supplied, is warranted for the warranty period stated above. If any such part fails during the period of warranty coverage, the part will be repaired or replaced by B&S at no charge to the owner. Any such part repaired or replaced under the warranty will be warranted for the remaining warranty period.

•Any warranted part that is scheduled only for regular inspection in the owner’s manual supplied, is warranted for the warranty period stated above. Any such part repaired or replaced under warranty will be warranted for the remaining warranty period.

•Any warranted part that is scheduled for replacement as required maintenance in the owner’s manual supplied, is warranted for the period of time prior to the first scheduled replacement point for that part. If the part fails prior to the first scheduled replacement, the part will be repaired or replaced by B&S at no charge to the owner. Any such part repaired or replaced under warranty will be warranted for the remainder of the period prior to the first scheduled replacement point for the part.

•Add on or modified parts that are not exempted by the Air Resources Board may not be used. The use of any non exempted add on or modified parts by the owner will be grounds for disallowing a warranty claim. The manufacturer will not be liable to warrant failures of warranted parts caused by the use of a non exempted add on or modified part.

3.Consequential Coverage

Coverage shall extend to the failure of any engine components caused by the failure of any warranted emissions parts.

4.Claims and Coverage Exclusions

Warranty claims shall be filed according to the provisions of the B&S engine warranty policy. Warranty coverage does not apply to failures of emissions parts that are not original equipment B&S parts or to parts that fail due to abuse, neglect, or improper maintenance as set forth in the B&S engine warranty policy. B&S is not liable for warranty coverage of failures of emissions parts caused by the use of add-on or modified parts.

Look For Relevant Emissions Durability Period and Air Index Information On Your Engine Emissions Label

Engines that are certified to meet the California Air Resources Board (CARB) Emissions Standard must display information regarding the Emissions Durability Period and the Air Index. Briggs & Stratton makes this information available to the consumer on our emissions labels. The engine emissions label will indicate certification information.

The Emissions Durability Period describes the number of hours of actual running time for which the engine is certified to be emissions compliant, assuming proper maintenance in accordance with the Operating & Maintenance Instructions. The following categories are used:

Moderate:

Engine is certified to be emissions compliant for 125 hours of actual engine running time.

Intermediate:

Engine is certified to be emissions compliant for 250 hours of actual engine running time.

Extended:

Engine is certified to be emissions compliant for 500 hours of actual engine running time.

For example, a typical walk-behind lawn mower is used 20 to 25 hours per year. Therefore, the Emissions Durability Period of an engine with an intermediate rating would equate to 10 to 12 years. Briggs & Stratton engines are certified to meet the United States Environmental Protection Agency (USEPA) Phase 2 emissions standards. For Phase 2 certified engines, the Emissions Compliance Period referred to on the Emissions Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emissions requirements.

For engines less than 225 cc displacement. Category C = 125 hours

Category B = 250 hours Category A = 500 hours

For engines of 225 cc or more displacement. Category C = 250 hours

Category B = 500 hours Category A = 1000 hours

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Operator’s Manual Generator Where to Find UsEngine Date PurchasedTable of Contents Important Safety Information Operator SafetySafety Symbols and Meanings Equipment DescriptionWhen Starting Equipment When Adding or Draining FuelWhen Operating Equipment When Transporting or Repairing EquipmentExcessively low speeds impose a heavy load When Testing for Engine SparkInstall Wheel Kit AssemblyInstall the wheel kit as follows Unpack GeneratorAdd Engine Oil When Adding FuelAdd Fuel Fuel must meet these requirementsSystem Ground Connecting to a Building’s Electrical SystemGenerator Location Special RequirementsItems Not Shown Features and ControlsNema L14-20 Cord Sets and Receptacles120/240 Volt AC, 20 Amp, Locking Receptacle Volt AC, 20 Amp, Duplex ReceptacleStarting the Engine OperationConnecting Electrical Loads Stopping the EngineWarm Weather Operation Wattage Reference Guide Don’t Overload GeneratorMaintenance Schedule MaintenanceGenerator Maintenance Fuel Valve MaintenanceOil Engine MaintenanceService Spark Plug Service Air CleanerClean and inspect the spark arrester as follows Inspect Muffler and Spark ArresterStorage Troubleshooting Manufacturer’s Warranty Coverage Your Warranty Rights And ObligationsOwner’s Warranty Responsibilities Briggs & Stratton Emissions Control Warranty ProvisionsModerate IntermediateExtended Limited Warranty Reserved Product Specifications Common Service Parts800 Manual del Operario Generador Dónde encontrarnosMotor Fecha de compraSeguridad de operario Resolución de problemas GarantíasMontaje Controles y característicasDescripción del equipo Seguridad de operarioInformación importante de seguridad Símbolos sobre la seguridad y significadosCuando Ponga EN Funcionamiento EL Equipo Cuando Anada Combustible O Vacíe EL DepósitoCuando Opere EL Equipo Cuando Transporte O Repare EL EquipoCuando Pruebe LA Bujía DEL Motor Cuando Ajuste O Haga Reparaciones a SU Máquina GeneradorDesembalaje del generador MontajeInstale el juego de ruedas El generador se entrega conAgregue combustible Agregar aceite al motorEl combustible debe reunir los siguientes requisitos Gran altitudConexión al sistema eléctrico de un edificio Tierra del sistemaUbicación del generador Requisitos especialesNo mostrado Controles y característicasJuegos de cordones y enchufes conectores Dispositivo de seguridad de 120/240 V, 20 aTomas eléctricas dobles de 120 V CA y 20 a Encienda el motor OperandoConexión de cargas eléctricas Parada del motorFuncionamiento en clima cálido Capacidad No sobrecargar el generadorEjemplo Control de la energíaMantenimiento Plan de mantenimientoMantenimiento del generador Mantenimiento del motor Mantenimiento de la válvula de combustibleAceite Recomendaciones sobre el aceite Comprobación del nivel de aceiteCambio de aceite del motor Servicio del depurador de aireServicio del bujía Limpie e inspeccione el apagachispas de la siguiente manera Inspeccione el silenciador y la pantalla apagachispasSistema de refrigeración de aire Ajuste del carburadorGenerador AlmacenamientoAlmacenamiento para periodos prolongados Cambio de aceiteProblemo Causa Accion Resolución de problemasDerechos y obligaciones de la garantía GarantíasCobertura de la garantía del fabricante Responsabilidades de la garantía del propietarioBRIGGSandSTRATTON.COM Garantía Limitada Servicio común despide Especificaciones del producto
Top Page Image Contents