Briggs & Stratton 209443gs manual Assembly, Unpack Generator, Install Wheel Kit

Page 7

Assembly

Read entire operator’s manual before you attempt to assemble or operate your new generator.

Your generator requires some assembly and is ready for use after it has been properly serviced with the recommended oil and fuel.

If you have any problems with the assembly of your generator, please call the generator helpline at (800) 743-4115. If calling for assistance, please have the model, revision, and serial number from the identification label available. See Generator Features and Controls for identification label location.

You will need the following tools to install these components:

•10 mm and 13 mm wrenches

•Socket wrench with 10 mm and 13 mm sockets

•Adjustable wrenches (2)

Install the wheel kit as follows:

1.Tip generator so that engine end is up.

2.Place axle stud (A) through mounting bracket on generator frame.

3.Place a flat washer (B) on axle stud as shown.

4.Use adjustable wrenches to secure the axle stud to frame with jam nut (C).

Unpack Generator

1.Set the carton on a rigid, flat surface.

2.Remove everything from carton except generator.

3.Open carton completely by cutting each corner from top to bottom.

4.Leave generator on carton to install wheel kit.

The generator is supplied with:

•Engine oil bottle

•Operator’s manual

•Wheel kit

Install Wheel Kit

NOTICE Wheel kit is not intended for over-the-road use.

5.Place a flat washer (B), then wheel (D) on axle as shown.

NOTICE Be sure to install wheel with raised hub inboard.

6.Use an adjustable wrench to secure the wheel to axle stud with jam nut.

7.Repeat steps 2 through 6 for other wheel.

8.Tip generator so that engine side is down.

9.Line up holes in support leg (E) with holes in generator frame.

10.Attach support leg using two 20 mm bolts (F) and two hex nuts (G). Tighten with 10 mm and 13 mm wrenches.

11.Return generator to normal operating position (resting on wheels and support legs).

12.Line up holes in handle (H) with holes in generator frame. Attach handle using 10 mm and 13 mm wrenches with 35 mm bolts (J) and hex nuts (K).

K

J

H

B

A

D

G

E

F C

7

Image 7

Contents Operator’s Manual Date Purchased Where to Find UsGenerator EngineTable of Contents Equipment Description Operator SafetyImportant Safety Information Safety Symbols and MeaningsWhen Transporting or Repairing Equipment When Adding or Draining FuelWhen Starting Equipment When Operating EquipmentExcessively low speeds impose a heavy load When Testing for Engine SparkUnpack Generator AssemblyInstall Wheel Kit Install the wheel kit as followsFuel must meet these requirements When Adding FuelAdd Engine Oil Add FuelSpecial Requirements Connecting to a Building’s Electrical SystemSystem Ground Generator LocationItems Not Shown Features and ControlsVolt AC, 20 Amp, Duplex Receptacle Cord Sets and ReceptaclesNema L14-20 120/240 Volt AC, 20 Amp, Locking ReceptacleStarting the Engine OperationStopping the Engine Connecting Electrical LoadsWarm Weather Operation Wattage Reference Guide Don’t Overload GeneratorFuel Valve Maintenance MaintenanceMaintenance Schedule Generator MaintenanceOil Engine MaintenanceInspect Muffler and Spark Arrester Service Air CleanerService Spark Plug Clean and inspect the spark arrester as followsStorage Troubleshooting Briggs & Stratton Emissions Control Warranty Provisions Your Warranty Rights And ObligationsManufacturer’s Warranty Coverage Owner’s Warranty ResponsibilitiesIntermediate ModerateExtended Limited Warranty Reserved Common Service Parts Product Specifications800 Manual del Operario Fecha de compra Dónde encontrarnosGenerador MotorControles y características Resolución de problemas GarantíasSeguridad de operario MontajeSímbolos sobre la seguridad y significados Seguridad de operarioDescripción del equipo Información importante de seguridadCuando Transporte O Repare EL Equipo Cuando Anada Combustible O Vacíe EL DepósitoCuando Ponga EN Funcionamiento EL Equipo Cuando Opere EL EquipoCuando Pruebe LA Bujía DEL Motor Cuando Ajuste O Haga Reparaciones a SU Máquina GeneradorEl generador se entrega con MontajeDesembalaje del generador Instale el juego de ruedasGran altitud Agregar aceite al motorAgregue combustible El combustible debe reunir los siguientes requisitosRequisitos especiales Tierra del sistemaConexión al sistema eléctrico de un edificio Ubicación del generadorNo mostrado Controles y característicasDispositivo de seguridad de 120/240 V, 20 a Juegos de cordones y enchufes conectoresTomas eléctricas dobles de 120 V CA y 20 a Encienda el motor OperandoParada del motor Conexión de cargas eléctricasFuncionamiento en clima cálido Control de la energía No sobrecargar el generadorCapacidad EjemploPlan de mantenimiento MantenimientoMantenimiento del generador Comprobación del nivel de aceite Mantenimiento de la válvula de combustibleMantenimiento del motor Aceite Recomendaciones sobre el aceiteServicio del depurador de aire Cambio de aceite del motorServicio del bujía Ajuste del carburador Inspeccione el silenciador y la pantalla apagachispasLimpie e inspeccione el apagachispas de la siguiente manera Sistema de refrigeración de aireCambio de aceite AlmacenamientoGenerador Almacenamiento para periodos prolongadosProblemo Causa Accion Resolución de problemasResponsabilidades de la garantía del propietario GarantíasDerechos y obligaciones de la garantía Cobertura de la garantía del fabricanteBRIGGSandSTRATTON.COM Garantía Limitada Servicio común despide Especificaciones del producto