Briggs & Stratton 30325 manual Generator Adapter Cord SET, Connecting Electrical Loads

Page 10

OPERATION

Connecting Electrical Loads

•Let engine stabilize and warm up for a few minutes after starting.

•Plug in and turn on the desired 120 and/or 240 Volt AC, single phase, 60 Hz electrical loads.

•DO NOT connect 240 Volt loads to the 120 Volt duplex receptacles.

•DO NOT connect 3–phase loads to the generator.

•DO NOT connect 50 Hz loads to the generator.

•DO NOT OVERLOAD THE GENERATOR. See “Don’t Overload Generator”.

CAUTION

Exceeding generators wattage/amperage capacity can damage generator and/or electrical devices connected to it.

•See “Don’t Overload Generator”.

•Start generator and let engine stabilize before connecting electrical loads.

•Connect electrical loads in OFF position, then turn ON for operation.

•Turn electrical loads OFF and disconnect from generator before stopping generator.

Stopping the Engine

1.Turn OFF and unplug all electrical loads from generator panel receptacles. NEVER start or stop engine with electrical devices plugged in and turned ON.

2.Let engine run at no-load for several minutes to stabilize internal temperatures of engine and generator.

3.Move on/off switch to “Off” position.

WARNING

Backfire, fire or engine damage could occur.

•DO NOT stop engine by moving choke lever to “Choke” position.

GENERATOR ADAPTER CORD SET

The generator is equipped with a 25’ generator adapter cord set designed for a 240 Volt, 30 Amp grounded neutral circuit (Figure 7).

Figure 7 — Generator Adapter Cord Set

The maximum load on each outlet is 20 Amps.The maximum total load on both yellow wire outlets or both black wire outlets is 30 Amps.

NOTE: Follow all safety precautions when connecting any extension cord or device to the generator.

4.Move fuel valve to “Off” position.

10

Image 10

Contents Operator’s Manual Manual del Operario Starting WattsCall Generator Helpline Llame Línea Directa del Generador Safety Rules Table of ContentsEquipment Description When Operating Equipment When Adding or Draining FuelWhen Starting Equipment When Transporting or Repairing EquipmentWhen Adjusting or Making Repairs to Your Generator When Testing for Engine SparkKnow Your Generator Recoil StarterRefer to and install the wheel kit as follows AssemblyInstall Wheel Kit Always wear eye protection when installing/removing e-ringsAdd Fuel Before Starting the EngineAdd Engine Oil Type of FuelSystem Ground Using the GeneratorConnecting to a Building’s Electrical System Generator LocationOperating Generator Starting the EngineStopping the Engine Connecting Electrical LoadsGenerator Adapter Cord SET Do not Overload the GENERATOR. See Don’t Overload Generator120/240 Volt AC, 30 Amp, Locking Receptacle ReceptaclesVolt AC, 20 Amp, Duplex Receptacles Capacity Power ManagementDont Overload Generator ExampleGenerator Specifications Product SpecificationsPower Ratings Engine SpecificationsGenerator Cleaning Generator MaintenanceGeneral Recommendations Servicing Air Cleaner Engine MaintenanceOil Changing Engine Oil To service the air cleaner, follow these stepsServicing Spark Arrester Clean and inspect the spark arrester as follows Clean Cooling SystemCarburetor Adjustment Servicing Spark PlugProtect Fuel System StorageLong Term Storage Instructions GeneratorTroubleshooting Emissions Control System Warranty Owner’s Warranty ResponsibilitiesPage Page Limited Warranty Descripción DEL Equipo Conserve Estas InstruccionesTabla DE Contenidos Reglas DE SeguridadCuando Opere EL Equipo Cuando Añada Combustible O Vacíe EL DepósitoCuando Ponga EN Funcionamiento EL Equipo Cuando Transporte O Repare EL EquipoCuando Ajuste O Haga Reparaciones a SU Generador PrecauciónCuando Pruebe LA Bujía DEL Motor Conozca SU Generador Tomacorriente con Dispositivo de Seguridad deInstale el Juego de Ruedas MontajeDesembalaje del Generador Tornillos Tuerca de Seguridad AsaAgregue Combustible Antes DE Darle Arranque AL MotorAgregar Aceite al Motor Cuando Añada CombustibleUbicación del Generador USO DEL GeneradorTierra del Sistema Conexión al Sistema Eléctrico de un EdificioOperando EL Generador Encienda el MotorParado Del Motor Juego DE Cables DEL Adaptador DEL GeneradorConexion De Cargas Electricas No Sobrecargue EL GENERADOR.Vea No Sobrecargue GeneradorVolt AC, 20 Amp, Receptáculos Dobles Receptáculos Precaución120/240 Voltios AC, 30 Amp, Receptáculo de Seguridad Juego de Cable de 4 Alambres 240V 120V Neutro CargadoControl de la Energía No Sobrecargue GeneradorCapacidad EjemploPotencia Nominal Información Técnica Sobre EL MotorEspecificaciones DEL Producto Especificaciones del GeneradorMantenimiento DEL Generador Recomendaciones GeneralesLimpieza del Generador Aceite Mantenimiento DEL Motor AdvertenciaServicio del Depurador de Aire Cartucho Cambio de Aceite del MotorLimpie la Pantalla Apagachispas TapaCompruebe la Holgura de la Válvula Limpie/Reemplace la BujíaSistema de Refrigeración de Aire Ajuste del CarburadorProteja el Sistema de Combustible AlmacenamientoAlmacenamiento Para Periodos Prolongados GeneradorProblemo Causa Accion Diagnositicos DE AveríasGarantía DEL Sistema DE Control DE Emisiones = 250 horas, B = 500 horas y a = 1000 horas Uso del consumidor Uso comercial