Briggs & Stratton 30325 manual Assembly, Unpack the Generator, Install Wheel Kit

Page 6

ASSEMBLY

ASSEMBLY

Refer to Figure 1 and install the wheel kit as follows:

1.Tip generator so that engine end is up.

Your generator requires some assembly and is ready for use after it has been properly serviced with the recommended oil and fuel.

If you have any problems with the assembly of your generator, please call the generator helpline at

1-800-743-4115. If calling for assistance, please have the model, revision, and serial number from the data tag available. See “Know Your Generator” for data tag location.

Unpack the Generator

1.Set the carton on a rigid flat surface.

2.Remove everything from carton except generator.

3.Open carton completely by cutting each corner from top to bottom.

4.Leave generator on carton to install wheel kit.

Install Wheel Kit

NOTE: Wheel kit is not intended for over-the-road use. You will need the following tools to install these components:

•2 - 13mm wrenches

•Socket wrench with a 13mm socket

•Pliers

•Safety glasses

Figure 1 — Install Wheel Kit

2.Slide axle through both mounting brackets.

3.Place a wheel on each side with raised hub inboard.

4.Place a washer on axle and then place an e-ring in axle groove.

5.Install e-ring with pliers, squeezing from top of e-ring to bottom of axle.

CAUTION

E-rings can cause eye injury.

E-rings can spring back and become airborne when installing or removing.

• Always wear eye protection when installing/removing e-rings.

6.Repeat step 4 and 5 to secure second wheel.

7.Tip generator so that engine side is down.

8.Line up holes in support leg with holes in generator frame.

9.Attach support leg using 2 capscrews (M8 x 16 mm) and 2 hex nuts.Tighten with a 13mm socket wrench and 13mm wrench.

10.On support leg end of generator, slide handle onto center of top of frame.

Capscrew
Nut
Handle
		Washer
	Axle
Support Leg	Capscrew
Nut	Wheel	E-Ring
	6

Image 6

Contents Starting Watts Operator’s Manual Manual del OperarioCall Generator Helpline Llame Línea Directa del Generador Table of Contents Safety RulesEquipment Description When Operating Equipment When Adding or Draining FuelWhen Starting Equipment When Transporting or Repairing EquipmentWhen Adjusting or Making Repairs to Your Generator When Testing for Engine SparkKnow Your Generator Recoil StarterRefer to and install the wheel kit as follows AssemblyInstall Wheel Kit Always wear eye protection when installing/removing e-ringsAdd Fuel Before Starting the EngineAdd Engine Oil Type of FuelSystem Ground Using the GeneratorConnecting to a Building’s Electrical System Generator LocationOperating Generator Starting the EngineStopping the Engine Connecting Electrical LoadsGenerator Adapter Cord SET Do not Overload the GENERATOR. See Don’t Overload GeneratorReceptacles 120/240 Volt AC, 30 Amp, Locking ReceptacleVolt AC, 20 Amp, Duplex Receptacles Capacity Power ManagementDont Overload Generator ExampleGenerator Specifications Product SpecificationsPower Ratings Engine SpecificationsGenerator Maintenance Generator CleaningGeneral Recommendations Engine Maintenance Servicing Air CleanerOil To service the air cleaner, follow these steps Changing Engine OilServicing Spark Arrester Clean and inspect the spark arrester as follows Clean Cooling SystemCarburetor Adjustment Servicing Spark PlugProtect Fuel System StorageLong Term Storage Instructions GeneratorTroubleshooting Emissions Control System Warranty Owner’s Warranty ResponsibilitiesPage Page Limited Warranty Descripción DEL Equipo Conserve Estas InstruccionesTabla DE Contenidos Reglas DE SeguridadCuando Opere EL Equipo Cuando Añada Combustible O Vacíe EL DepósitoCuando Ponga EN Funcionamiento EL Equipo Cuando Transporte O Repare EL EquipoPrecaución Cuando Ajuste O Haga Reparaciones a SU GeneradorCuando Pruebe LA Bujía DEL Motor Conozca SU Generador Tomacorriente con Dispositivo de Seguridad deInstale el Juego de Ruedas MontajeDesembalaje del Generador Tornillos Tuerca de Seguridad AsaAgregue Combustible Antes DE Darle Arranque AL MotorAgregar Aceite al Motor Cuando Añada CombustibleUbicación del Generador USO DEL GeneradorTierra del Sistema Conexión al Sistema Eléctrico de un EdificioOperando EL Generador Encienda el MotorParado Del Motor Juego DE Cables DEL Adaptador DEL GeneradorConexion De Cargas Electricas No Sobrecargue EL GENERADOR.Vea No Sobrecargue GeneradorVolt AC, 20 Amp, Receptáculos Dobles Receptáculos Precaución120/240 Voltios AC, 30 Amp, Receptáculo de Seguridad Juego de Cable de 4 Alambres 240V 120V Neutro CargadoControl de la Energía No Sobrecargue GeneradorCapacidad EjemploPotencia Nominal Información Técnica Sobre EL MotorEspecificaciones DEL Producto Especificaciones del GeneradorRecomendaciones Generales Mantenimiento DEL GeneradorLimpieza del Generador Mantenimiento DEL Motor Advertencia AceiteServicio del Depurador de Aire Cartucho Cambio de Aceite del MotorLimpie la Pantalla Apagachispas TapaCompruebe la Holgura de la Válvula Limpie/Reemplace la BujíaSistema de Refrigeración de Aire Ajuste del CarburadorProteja el Sistema de Combustible AlmacenamientoAlmacenamiento Para Periodos Prolongados GeneradorProblemo Causa Accion Diagnositicos DE AveríasGarantía DEL Sistema DE Control DE Emisiones = 250 horas, B = 500 horas y a = 1000 horas Uso del consumidor Uso comercial