Poulan 96192003302, 430355 Service And Adjustments, Engine, TO REMOVE WHEELS See Fig, Carburetor

Page 17

TO REMOVE WHEELS (See Fig. 21)

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 21)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

KLIK PIN	OUTER HOLE
	INNER
	HOLE
WHEEL	WHEEL HUB

FIG. 21

TO ADJUST CABLE TENSION (See Fig. 22)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 22

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

17

Image 17

Contents SNOW THROWER OWNERS MANUAL MODEL NUMBERIMPORTANT MANUAL XT824ESTraining Safe Operation Practices for Walk-Behind Snow ThrowersPreparation OperationPRODUCT SPECIFICATIONS TABLE OF CONTENTSMaintenance and Storage CUSTOMER RESPONSIBILITIESHOW TO SET UP YOUR SNOW THROWER ASSEMBLY / PRE-OPERATIONPARTS PACKED SEPARATELY IN CARTON REMOVE SNOW THROWER FROM CARTONUNFOLD UPPER HANDLE INSTALL SPEED CONTROL ROD See Figs. 1 andINSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and CHECK TIRE PRESSURE INSTALL AUGER CONTROL ROD See Figs. 5 andINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD See Fig KNOW YOUR SNOW THROWER OPERATIONRecoil auxiliary starter handle - used for starting the engine MEETS A.N.S.I. SAFETY REQUIREMENTSSTOPPING HOW TO USE YOUR SNOW THROWERTO USE CHOKE CONTROL See Fig TO CONTROL SNOW DISCHARGE See FigsTO THROW SNOW See Fig USING THE CLEAN-OUT TOOL See FigTO MOVE FORWARD AND BACKWARD See Fig AUGER CONTROL LEVERTO ADJUST SKID PLATES See Fig BEFORE STARTING THE ENGINESCRAPER BAR See Fig CHECK ENGINE OIL LEVEL See FigTO START ENGINE SNOW THROWING TIPSBEFORE STOPPING IF RECOIL STARTER HAS FROZENLUBRICATION CHART MAINTENANCEGENERAL RECOMMENDATIONS BEFORE EACH USEENGINE CLEANINGAUGER GEAR CASE TRACTION DRIVE SYSTEM1. Be sure the on/off switch is in the OFF position SERVICE AND ADJUSTMENTS2. Remove safety ignition key TO ADJUST SNOW THROWER HEIGHTTO REPLACE BELTS See Fig TO REMOVE WHEELS See Fig TO ADJUST CABLE TENSION See FigCARBURETOR ENGINE SPEEDOTHER STORAGEFUEL SYSTEM ENGINE OILLoss of power TROUBLESHOOTINGDoes not start Engine idles orAUGER HOUSING / IMPELLER ASSEMBLY REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES01.07.026-C 2 EXPLODEDDESCRIPTION PARTAUGER HOUSING / IMPELLER ASSEMBLY REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ESPART DESCRIPTIONAUGER HOUSING / IMPELLER ASSEMBLY 01.09.010-B CONTROL PANEL / DISCHARGE CHUTECONTROL PANEL / DISCHARGE CHUTE 01.10.019 REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES HANDLESPART 01.08.002-F 01.12.001-E HANDLES01.02.013-A REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES DRIVE42 EXPLODED PART assy of 1a,1b AXLE ASSEMBLY 423185X505 CHASSIS / ENGINE / PULLEYSENGINE MOUNTING PLATE 428684CHASSIS / ENGINE / PULLEYS WHEEL ASSEMBLY RH REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES WHEELS193071 REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES BAG OF PARTSSAFETY IGNITION KEY DECAL, DANGER DECALS181037 SERVICE NOTES SERVICE NOTES LIMITED WARRANTY