Poulan 96192003302, 430355 owner manual Assembly / Pre-Operation, Unfold Upper Handle

Page 5

UNFOLD UPPER HANDLE

ASSEMBLY / PRE-OPERATION

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates.

UNFOLD UPPER HANDLE

1.Raise upper handle to the operating position and tighten handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to lower handle. Install in lower holes in handles.

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1.Remove plastic tie securing rod to lower handle.

2.Insert rod into speed control bracket and secure with retainer spring.

SPEED

CONTROL

ROD

PLASTIC TIE

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

FIG. 1

SPEED CONTROL ROD
	RETAINER
	SPRING
SPEED	SPEED
CONTROL	CONTROL
BRACKET	LEVER

FIG. 2

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod is installed on the snow thrower.

1.Remove plastic tie securring rod to lower handle.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

PLASTIC TIE

TRACTION DRIVE

CONTROL ROD

VINYL

SLEEVE

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING
	TRACTION
	DRIVE
	CONTROL
	ROD
DRIVE
CONTROL
BRACKET

FIG. 4

5

Image 5

Contents SNOW THROWER OWNERS MANUAL MODEL NUMBERIMPORTANT MANUAL XT824ESTraining Safe Operation Practices for Walk-Behind Snow ThrowersPreparation OperationPRODUCT SPECIFICATIONS TABLE OF CONTENTSMaintenance and Storage CUSTOMER RESPONSIBILITIESHOW TO SET UP YOUR SNOW THROWER ASSEMBLY / PRE-OPERATIONPARTS PACKED SEPARATELY IN CARTON REMOVE SNOW THROWER FROM CARTONUNFOLD UPPER HANDLE INSTALL SPEED CONTROL ROD See Figs. 1 andINSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and CHECK TIRE PRESSURE INSTALL AUGER CONTROL ROD See Figs. 5 andINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD See Fig KNOW YOUR SNOW THROWER OPERATIONRecoil auxiliary starter handle - used for starting the engine MEETS A.N.S.I. SAFETY REQUIREMENTSSTOPPING HOW TO USE YOUR SNOW THROWERTO USE CHOKE CONTROL See Fig TO CONTROL SNOW DISCHARGE See FigsTO THROW SNOW See Fig USING THE CLEAN-OUT TOOL See FigTO MOVE FORWARD AND BACKWARD See Fig AUGER CONTROL LEVERTO ADJUST SKID PLATES See Fig BEFORE STARTING THE ENGINESCRAPER BAR See Fig CHECK ENGINE OIL LEVEL See FigTO START ENGINE SNOW THROWING TIPSBEFORE STOPPING IF RECOIL STARTER HAS FROZENLUBRICATION CHART MAINTENANCEGENERAL RECOMMENDATIONS BEFORE EACH USEENGINE CLEANINGAUGER GEAR CASE TRACTION DRIVE SYSTEM1. Be sure the on/off switch is in the OFF position SERVICE AND ADJUSTMENTS2. Remove safety ignition key TO ADJUST SNOW THROWER HEIGHTTO REPLACE BELTS See Fig TO REMOVE WHEELS See Fig TO ADJUST CABLE TENSION See FigCARBURETOR ENGINE SPEEDOTHER STORAGEFUEL SYSTEM ENGINE OILLoss of power TROUBLESHOOTINGDoes not start Engine idles orAUGER HOUSING / IMPELLER ASSEMBLY REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES01.07.026-C 2 EXPLODEDDESCRIPTION PARTAUGER HOUSING / IMPELLER ASSEMBLY REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ESPART DESCRIPTIONAUGER HOUSING / IMPELLER ASSEMBLY 01.09.010-B CONTROL PANEL / DISCHARGE CHUTECONTROL PANEL / DISCHARGE CHUTE 01.10.019 REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES HANDLESPART 01.08.002-F 01.12.001-E HANDLES01.02.013-A REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES DRIVE42 EXPLODED PART assy of 1a,1b AXLE ASSEMBLY 423185X505 CHASSIS / ENGINE / PULLEYSENGINE MOUNTING PLATE 428684CHASSIS / ENGINE / PULLEYS WHEEL ASSEMBLY RH REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES WHEELS193071 REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES BAG OF PARTSSAFETY IGNITION KEY DECAL, DANGER DECALS181037 SERVICE NOTES SERVICE NOTES LIMITED WARRANTY