Poulan 430355 REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES, Auger Housing / Impeller Assembly

Page 22

REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES (96192003302)

AUGER HOUSING / IMPELLER ASSEMBLY

KEY	PART
NO.	NO.	DESCRIPTION
1	404928X505	AUGER HOUSING
2	404931X479	SCRAPER BAR
3	72270505	CARRIAGE BOLT 5/16−18 X .625
4	155377	NUT 5/16−18

3 (5x) 4 (5x)

01.07.001-A

2	3

	KEY	PART
	NO.	NO.	DESCRIPTION
3	1	420478	AUGER BEARING
3	2	411939	BEARING PLUG
	2	411939	BEARING PLUG
01.07.024-B	3	179582	SCREW 5/16−18 X 1.00

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 22

Image 22

Contents IMPORTANT MANUAL OWNERS MANUAL MODEL NUMBERSNOW THROWER XT824ESPreparation Safe Operation Practices for Walk-Behind Snow ThrowersTraining OperationMaintenance and Storage TABLE OF CONTENTSPRODUCT SPECIFICATIONS CUSTOMER RESPONSIBILITIESPARTS PACKED SEPARATELY IN CARTON ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER REMOVE SNOW THROWER FROM CARTONINSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and INSTALL SPEED CONTROL ROD See Figs. 1 andUNFOLD UPPER HANDLE INSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD See Fig INSTALL AUGER CONTROL ROD See Figs. 5 andCHECK TIRE PRESSURE OPERATION KNOW YOUR SNOW THROWERMEETS A.N.S.I. SAFETY REQUIREMENTS Recoil auxiliary starter handle - used for starting the engineTO USE CHOKE CONTROL See Fig HOW TO USE YOUR SNOW THROWERSTOPPING TO CONTROL SNOW DISCHARGE See FigsTO MOVE FORWARD AND BACKWARD See Fig USING THE CLEAN-OUT TOOL See FigTO THROW SNOW See Fig AUGER CONTROL LEVERSCRAPER BAR See Fig BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig CHECK ENGINE OIL LEVEL See FigBEFORE STOPPING SNOW THROWING TIPSTO START ENGINE IF RECOIL STARTER HAS FROZENGENERAL RECOMMENDATIONS MAINTENANCELUBRICATION CHART BEFORE EACH USEAUGER GEAR CASE CLEANINGENGINE TRACTION DRIVE SYSTEM2. Remove safety ignition key SERVICE AND ADJUSTMENTS1. Be sure the on/off switch is in the OFF position TO ADJUST SNOW THROWER HEIGHTTO REPLACE BELTS See Fig CARBURETOR TO ADJUST CABLE TENSION See FigTO REMOVE WHEELS See Fig ENGINE SPEEDFUEL SYSTEM STORAGEOTHER ENGINE OILDoes not start TROUBLESHOOTINGLoss of power Engine idles or01.07.026-C REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ESAUGER HOUSING / IMPELLER ASSEMBLY 2 EXPLODEDPART DESCRIPTIONPART REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ESAUGER HOUSING / IMPELLER ASSEMBLY DESCRIPTIONPART CONTROL PANEL / DISCHARGE CHUTE 01.09.010-BPART REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES HANDLES 01.10.019DESCRIPTION 01.08.002-F HANDLES 01.12.001-E42 EXPLODED REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES DRIVE01.02.013-A PART assy of 1a,1b AXLE ASSEMBLY ENGINE MOUNTING PLATE CHASSIS / ENGINE / PULLEYS423185X505 428684PART REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES WHEELS WHEEL ASSEMBLY RHSAFETY IGNITION KEY REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES BAG OF PARTS193071 181037 DECALSDECAL, DANGER SERVICE NOTES SERVICE NOTES LIMITED WARRANTY