Poulan 430355 REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES HANDLES, 01.10.019, Part

Page 26

REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES (96192003302)

HANDLES

					5
						1
					6
					8	7
					2
		5		8	3	9
				8
KEY	PART		6		7
NO.	NO.	DESCRIPTION			7
NO.	NO.	DESCRIPTION
1	419800X479	PLOW HANDLE LH		8
2	419801X479	PLOW HANDLE RH			4 9
3	196944X007	PANEL BRACKET LH
4	196943X007	PANEL BRACKET RH
5	199513	HANDLE GRIP

674780512 SCREW 5/16−18 X .750

774780524 SCREW 5/16−18 X 1.50

8	751153	NUT 5/16−18
9	155415	WASHER	01.08.003-A
			01.08.003-A

	7	1	4
		1	4
	3
	2		5
	2
		4	KEY	PART
6	5		NO.	NO.	DESCRIPTION
6	5		1	429620	CONSOLE PANEL
			1	429620	CONSOLE PANEL
			2	178668	HEADLIGHT BEZEL
			3	180927	FLOOD HEADLIGHT
	01.10.019		4	184471	SHOULDERSCREW10−24X.625
	01.10.019		5	175262	SCREW 10−24 X 1.25
			5	175262	SCREW 10−24 X 1.25
			6	178770	WIRE HARNESS
			7	183784	BULB

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 26

Image 26

Contents IMPORTANT MANUAL OWNERS MANUAL MODEL NUMBERSNOW THROWER XT824ESPreparation Safe Operation Practices for Walk-Behind Snow ThrowersTraining OperationMaintenance and Storage TABLE OF CONTENTSPRODUCT SPECIFICATIONS CUSTOMER RESPONSIBILITIESPARTS PACKED SEPARATELY IN CARTON ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER REMOVE SNOW THROWER FROM CARTONUNFOLD UPPER HANDLE INSTALL SPEED CONTROL ROD See Figs. 1 andINSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and CHECK TIRE PRESSURE INSTALL AUGER CONTROL ROD See Figs. 5 andINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD See Fig OPERATION KNOW YOUR SNOW THROWERMEETS A.N.S.I. SAFETY REQUIREMENTS Recoil auxiliary starter handle - used for starting the engineTO USE CHOKE CONTROL See Fig HOW TO USE YOUR SNOW THROWERSTOPPING TO CONTROL SNOW DISCHARGE See FigsTO MOVE FORWARD AND BACKWARD See Fig USING THE CLEAN-OUT TOOL See FigTO THROW SNOW See Fig AUGER CONTROL LEVERSCRAPER BAR See Fig BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig CHECK ENGINE OIL LEVEL See FigBEFORE STOPPING SNOW THROWING TIPSTO START ENGINE IF RECOIL STARTER HAS FROZENGENERAL RECOMMENDATIONS MAINTENANCELUBRICATION CHART BEFORE EACH USEAUGER GEAR CASE CLEANINGENGINE TRACTION DRIVE SYSTEM2. Remove safety ignition key SERVICE AND ADJUSTMENTS1. Be sure the on/off switch is in the OFF position TO ADJUST SNOW THROWER HEIGHTTO REPLACE BELTS See Fig CARBURETOR TO ADJUST CABLE TENSION See FigTO REMOVE WHEELS See Fig ENGINE SPEEDFUEL SYSTEM STORAGEOTHER ENGINE OILDoes not start TROUBLESHOOTINGLoss of power Engine idles or01.07.026-C REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ESAUGER HOUSING / IMPELLER ASSEMBLY 2 EXPLODEDPART DESCRIPTIONPART REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ESAUGER HOUSING / IMPELLER ASSEMBLY DESCRIPTIONPART CONTROL PANEL / DISCHARGE CHUTE 01.09.010-BPART REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES HANDLES 01.10.019DESCRIPTION 01.08.002-F HANDLES 01.12.001-E01.02.013-A REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES DRIVE42 EXPLODED PART assy of 1a,1b AXLE ASSEMBLY ENGINE MOUNTING PLATE CHASSIS / ENGINE / PULLEYS423185X505 428684PART REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES WHEELS WHEEL ASSEMBLY RH193071 REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES BAG OF PARTSSAFETY IGNITION KEY DECAL, DANGER DECALS181037 SERVICE NOTES SERVICE NOTES LIMITED WARRANTY