Poulan 430355 REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES, Chassis / Engine / Pulleys, Part

Page 34

Manual background

REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES (96192003302)

CHASSIS / ENGINE / PULLEYS

23		22	14
24			14	21
24				21
				20
11
14	21		20	19
13			20	18
13				18
12				17
12	14			16
		15		16
		15		6
				6
	7
10
				5
8				4
8				3
				3
				9

1

2

01.21.003-B

KEY	PART		KEY	PART
NO.	NO.	DESCRIPTION	NO.	NO.	DESCRIPTION
1	408007	IMPELLER BELT	13	74780520	SCREW 5/16-18 X 1 .00
2	419744	TRACTION BELT	14	59289	WASHER
3	423723X479	IDLER ARM BRACKET	15	73800500	NUT 5/16-18
4	180523	IDLER PULLEY	16	851084	SCREW 3/8-24 X 1.375
5	426589	NUT 5/16-18	17	400026	WASHER
6	74780524	SCREW 5/16-18 X 1 .50	18	426491	PULLEY ENG IMPELLER
7	423990X479	IDLER BRACKET	19	426490	PULLEY ENG TRACTION
8	428867	SCREW 5/16-18 X .625	20	74610516	SCREW 5/16-18 X 1 .00
9	424297	SHOULDER BOLT 5/16-18 X .500	21	10040500	LOCKWASHER 5/16
10	751153	NUT 5/16-18 NYLOCK	22	155452	BELT GUIDE
11	187786	TRACTION IDLER ARM	23	11050500	LOCKWASHER 5/16
12	180522	TRACTION PULLEY	24	175331	IDLER BUSHING

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

34

Image 34

Contents IMPORTANT MANUAL OWNERS MANUAL MODEL NUMBERSNOW THROWER XT824ESPreparation Safe Operation Practices for Walk-Behind Snow ThrowersTraining OperationMaintenance and Storage TABLE OF CONTENTSPRODUCT SPECIFICATIONS CUSTOMER RESPONSIBILITIESPARTS PACKED SEPARATELY IN CARTON ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER REMOVE SNOW THROWER FROM CARTONINSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and INSTALL SPEED CONTROL ROD See Figs. 1 andUNFOLD UPPER HANDLE INSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD See Fig INSTALL AUGER CONTROL ROD See Figs. 5 andCHECK TIRE PRESSURE OPERATION KNOW YOUR SNOW THROWERMEETS A.N.S.I. SAFETY REQUIREMENTS Recoil auxiliary starter handle - used for starting the engineTO USE CHOKE CONTROL See Fig HOW TO USE YOUR SNOW THROWERSTOPPING TO CONTROL SNOW DISCHARGE See FigsTO MOVE FORWARD AND BACKWARD See Fig USING THE CLEAN-OUT TOOL See FigTO THROW SNOW See Fig AUGER CONTROL LEVERSCRAPER BAR See Fig BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig CHECK ENGINE OIL LEVEL See FigBEFORE STOPPING SNOW THROWING TIPSTO START ENGINE IF RECOIL STARTER HAS FROZENGENERAL RECOMMENDATIONS MAINTENANCELUBRICATION CHART BEFORE EACH USEAUGER GEAR CASE CLEANINGENGINE TRACTION DRIVE SYSTEM2. Remove safety ignition key SERVICE AND ADJUSTMENTS1. Be sure the on/off switch is in the OFF position TO ADJUST SNOW THROWER HEIGHTTO REPLACE BELTS See Fig CARBURETOR TO ADJUST CABLE TENSION See FigTO REMOVE WHEELS See Fig ENGINE SPEEDFUEL SYSTEM STORAGEOTHER ENGINE OILDoes not start TROUBLESHOOTINGLoss of power Engine idles or01.07.026-C REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ESAUGER HOUSING / IMPELLER ASSEMBLY 2 EXPLODEDPART DESCRIPTIONPART REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ESAUGER HOUSING / IMPELLER ASSEMBLY DESCRIPTIONPART CONTROL PANEL / DISCHARGE CHUTE 01.09.010-BPART REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES HANDLES 01.10.019DESCRIPTION 01.08.002-F HANDLES 01.12.001-E42 EXPLODED REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES DRIVE01.02.013-A PART assy of 1a,1b AXLE ASSEMBLY ENGINE MOUNTING PLATE CHASSIS / ENGINE / PULLEYS423185X505 428684PART REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES WHEELS WHEEL ASSEMBLY RHSAFETY IGNITION KEY REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES BAG OF PARTS193071 181037 DECALSDECAL, DANGER SERVICE NOTES SERVICE NOTES LIMITED WARRANTY