Poulan 430355 REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES BAG OF PARTS, Part, Description

Page 36

REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES (96192003302)

REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES (96192003302)

BAG OF PARTS

3			KEY	PART
			KEY	PART
	4	5	NO.	NO.	DESCRIPTION
			1	198563	POWER CORD
			2	169675	RETAINER PIN
			3	180684X008	WRENCH
			4	73800600	LOCKNUT 3/8−16
			5	19131316	WASHER 3/8
			6	192090	SHEAR BOLT 1/4−20 X 1−3/4
2	1	7	7	73800400	LOCKNUT 1/4−20
	6
	01.14.004-B

	KEY	PART
	NO.	NO.	DESCRIPTION
1	1	193071	SAFETY IGNITION KEY

01.14.007-A

13

4

1	4
	2.56

2

2

01.14.012-A

KEY	PART
NO.	NO.	DESCRIPTION

1180445 SHIFTER ROD TOP

2187716 SHIFTER ROD BOTTOM

372270505 CARRIAGE BOLT 5/16-18 X .75

4

155377

NUT 5/16-18

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 36

Image 36

Contents OWNERS MANUAL MODEL NUMBER SNOW THROWERIMPORTANT MANUAL XT824ESSafe Operation Practices for Walk-Behind Snow Throwers TrainingPreparation OperationTABLE OF CONTENTS PRODUCT SPECIFICATIONSMaintenance and Storage CUSTOMER RESPONSIBILITIESASSEMBLY / PRE-OPERATION HOW TO SET UP YOUR SNOW THROWERPARTS PACKED SEPARATELY IN CARTON REMOVE SNOW THROWER FROM CARTONINSTALL SPEED CONTROL ROD See Figs. 1 and INSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 andUNFOLD UPPER HANDLE INSTALL AUGER CONTROL ROD See Figs. 5 and INSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD See FigCHECK TIRE PRESSURE OPERATION KNOW YOUR SNOW THROWERMEETS A.N.S.I. SAFETY REQUIREMENTS Recoil auxiliary starter handle - used for starting the engineHOW TO USE YOUR SNOW THROWER STOPPINGTO USE CHOKE CONTROL See Fig TO CONTROL SNOW DISCHARGE See FigsUSING THE CLEAN-OUT TOOL See Fig TO THROW SNOW See FigTO MOVE FORWARD AND BACKWARD See Fig AUGER CONTROL LEVERBEFORE STARTING THE ENGINE TO ADJUST SKID PLATES See FigSCRAPER BAR See Fig CHECK ENGINE OIL LEVEL See FigSNOW THROWING TIPS TO START ENGINEBEFORE STOPPING IF RECOIL STARTER HAS FROZENMAINTENANCE LUBRICATION CHARTGENERAL RECOMMENDATIONS BEFORE EACH USECLEANING ENGINEAUGER GEAR CASE TRACTION DRIVE SYSTEMSERVICE AND ADJUSTMENTS 1. Be sure the on/off switch is in the OFF position2. Remove safety ignition key TO ADJUST SNOW THROWER HEIGHTTO REPLACE BELTS See Fig TO ADJUST CABLE TENSION See Fig TO REMOVE WHEELS See FigCARBURETOR ENGINE SPEEDSTORAGE OTHERFUEL SYSTEM ENGINE OILTROUBLESHOOTING Loss of powerDoes not start Engine idles orREPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES AUGER HOUSING / IMPELLER ASSEMBLY01.07.026-C 2 EXPLODEDPART DESCRIPTIONREPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES AUGER HOUSING / IMPELLER ASSEMBLYPART DESCRIPTIONREPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES CONTROL PANEL / DISCHARGE CHUTE 01.09.010-BREPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES HANDLES 01.10.019REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES HANDLES 01.08.002-F HANDLES 01.12.001-EREPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES DRIVE 42 EXPLODED01.02.013-A REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES DRIVE assy of 1a,1b AXLE ASSEMBLY CHASSIS / ENGINE / PULLEYS 423185X505ENGINE MOUNTING PLATE 428684REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES WHEELS WHEEL ASSEMBLY RHREPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES BAG OF PARTS SAFETY IGNITION KEY193071 DECALS 181037DECAL, DANGER SERVICE NOTES SERVICE NOTES LIMITED WARRANTY