Poulan 430355 Parts Packed Separately In Carton, Assembly / Pre-Operation, TOOL BOX See Fig

Page 4

PARTS PACKED SEPARATELY IN CARTON

PARTS PACKED SEPARATELY IN CARTON

(1) FUEL STABILIZER PACKET	(1) MULTI-
	WRENCH
	(180684)

(1) POWER CORD	SAFTEY IGNITION KEY(S)
(198563)	(193071)
	(1) AUGER CONTROL ROD
(1) DISCHARGE CHUTE		(2) FLAT WASHERS
(1) DISCHARGE CHUTE
EXTRA SHEAR BOLTS AND NUTS
(2) SHOULDER	(2) LOCKNUTS	(2) CARRIAGE BOLTS
BOLT 1/4-20 x 1-3/4	1/4-20	3/8-16 x 2.25
(192090)	(73800400)

ROTATOR HEAD MOUNTING

(3) RETAINER

SPRINGS(2) HANDLE KNOBS (169675)

(1) WASHER 3/8	(1) LOCKNUT 3/8
(19131316)	(73800600)

CHUTE DEFLECTOR REMOTE CONTROL

(1) LOCKNUT	(1) CARRIAGE BOLT	(1) LOCKNUT	(1) SHOULDER	(1) SPRING
5/16-18	5/16-18 x 5/8	1/4-20	BOLT 1/4-20	(1) SPRING
(751153)	(72250505)	(191730)	(179829)	(184505)

ASSEMBLY / PRE-OPERATION

Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly, operation and maintenance of the product.

Your new snow thrower has been assembled at the factory with the exception of those parts left unassembled for ship- ping purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts bag. To ensure safe and proper operation of your snow thrower, all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness.

REMOVE SNOW THROWER FROM CARTON

1. Remove all accessible loose parts and parts boxes
from carton.	4
	4

2.Cut down all four corners of carton and lay panels flat.

3.Remove the two (2) screws securing the auger housing to the pallet.

4.Remove all packing materials except plastic tie holding speed control rod to lower handle.

5.Remove the two (2) plastic ties securing the upper handle to the pallet.

6.Remove snow thrower from carton and check carton thoroughly for additional loose parts.

HOW TO SET UP YOUR SNOW THROWER

TOOL BOX (See Fig. 8)

A toolbox is provided on your snow thrower. The toolbox is located on top of the belt cover. Store the extra shear bolts, nuts and multi-wrench provided in parts bag in the toolbox.

Image 4

Contents OWNERS MANUAL MODEL NUMBER SNOW THROWERIMPORTANT MANUAL XT824ESSafe Operation Practices for Walk-Behind Snow Throwers TrainingPreparation OperationTABLE OF CONTENTS PRODUCT SPECIFICATIONSMaintenance and Storage CUSTOMER RESPONSIBILITIESASSEMBLY / PRE-OPERATION HOW TO SET UP YOUR SNOW THROWERPARTS PACKED SEPARATELY IN CARTON REMOVE SNOW THROWER FROM CARTONINSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and INSTALL SPEED CONTROL ROD See Figs. 1 andUNFOLD UPPER HANDLE INSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD See Fig INSTALL AUGER CONTROL ROD See Figs. 5 andCHECK TIRE PRESSURE OPERATION KNOW YOUR SNOW THROWERMEETS A.N.S.I. SAFETY REQUIREMENTS Recoil auxiliary starter handle - used for starting the engineHOW TO USE YOUR SNOW THROWER STOPPINGTO USE CHOKE CONTROL See Fig TO CONTROL SNOW DISCHARGE See FigsUSING THE CLEAN-OUT TOOL See Fig TO THROW SNOW See FigTO MOVE FORWARD AND BACKWARD See Fig AUGER CONTROL LEVERBEFORE STARTING THE ENGINE TO ADJUST SKID PLATES See FigSCRAPER BAR See Fig CHECK ENGINE OIL LEVEL See FigSNOW THROWING TIPS TO START ENGINEBEFORE STOPPING IF RECOIL STARTER HAS FROZENMAINTENANCE LUBRICATION CHARTGENERAL RECOMMENDATIONS BEFORE EACH USECLEANING ENGINEAUGER GEAR CASE TRACTION DRIVE SYSTEMSERVICE AND ADJUSTMENTS 1. Be sure the on/off switch is in the OFF position2. Remove safety ignition key TO ADJUST SNOW THROWER HEIGHTTO REPLACE BELTS See Fig TO ADJUST CABLE TENSION See Fig TO REMOVE WHEELS See FigCARBURETOR ENGINE SPEEDSTORAGE OTHERFUEL SYSTEM ENGINE OILTROUBLESHOOTING Loss of powerDoes not start Engine idles orREPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES AUGER HOUSING / IMPELLER ASSEMBLY01.07.026-C 2 EXPLODEDPART DESCRIPTIONREPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES AUGER HOUSING / IMPELLER ASSEMBLYPART DESCRIPTIONREPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES CONTROL PANEL / DISCHARGE CHUTE 01.09.010-BREPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES HANDLES 01.10.019REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES HANDLES 01.08.002-F HANDLES 01.12.001-E42 EXPLODED REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES DRIVE01.02.013-A REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES DRIVE assy of 1a,1b AXLE ASSEMBLY CHASSIS / ENGINE / PULLEYS 423185X505ENGINE MOUNTING PLATE 428684REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES WHEELS WHEEL ASSEMBLY RHSAFETY IGNITION KEY REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES BAG OF PARTS193071 181037 DECALSDECAL, DANGER SERVICE NOTES SERVICE NOTES LIMITED WARRANTY