Poulan 430355 REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES HANDLES, Part, Description

Page 28

01.08.002-F

REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES (96192003302)

HANDLES

10

2

	11		7
	8	4	7
		4

	9
	9
	5
	7
	6
			1
3			12
3
	8		13
	8

13

01.08.002-F

14

14

12

KEY	PART
NO.	NO.	DESCRIPTION

1412683X479 CONTROL PANEL

2424517X479 CONTROL LEVER LH

3424516X479 CONTROL LEVER RH

4426917X008 TRACTION ROD ARM

5426918X008 IMPELLER ROD ARM

6412677 INTERLOCK ROD

7	421613	SPACER
8	169675	RETAINER
9	17060410	SCREW 1/4-20 X .62
10	414280	KNOB BLACK
11	414281	KNOB RED
12	178899	HANDLE KNOB
13	19131316	WASHER 3/8
14	72120618	CARRIAGE BOLT 3/8-16 X 2.25

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

28

Image 28

Contents OWNERS MANUAL MODEL NUMBER SNOW THROWERIMPORTANT MANUAL XT824ESSafe Operation Practices for Walk-Behind Snow Throwers TrainingPreparation OperationTABLE OF CONTENTS PRODUCT SPECIFICATIONSMaintenance and Storage CUSTOMER RESPONSIBILITIESASSEMBLY / PRE-OPERATION HOW TO SET UP YOUR SNOW THROWERPARTS PACKED SEPARATELY IN CARTON REMOVE SNOW THROWER FROM CARTONINSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and INSTALL SPEED CONTROL ROD See Figs. 1 andUNFOLD UPPER HANDLE INSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD See Fig INSTALL AUGER CONTROL ROD See Figs. 5 andCHECK TIRE PRESSURE OPERATION KNOW YOUR SNOW THROWERMEETS A.N.S.I. SAFETY REQUIREMENTS Recoil auxiliary starter handle - used for starting the engineHOW TO USE YOUR SNOW THROWER STOPPINGTO USE CHOKE CONTROL See Fig TO CONTROL SNOW DISCHARGE See FigsUSING THE CLEAN-OUT TOOL See Fig TO THROW SNOW See FigTO MOVE FORWARD AND BACKWARD See Fig AUGER CONTROL LEVERBEFORE STARTING THE ENGINE TO ADJUST SKID PLATES See FigSCRAPER BAR See Fig CHECK ENGINE OIL LEVEL See FigSNOW THROWING TIPS TO START ENGINEBEFORE STOPPING IF RECOIL STARTER HAS FROZENMAINTENANCE LUBRICATION CHARTGENERAL RECOMMENDATIONS BEFORE EACH USECLEANING ENGINEAUGER GEAR CASE TRACTION DRIVE SYSTEMSERVICE AND ADJUSTMENTS 1. Be sure the on/off switch is in the OFF position2. Remove safety ignition key TO ADJUST SNOW THROWER HEIGHTTO REPLACE BELTS See Fig TO ADJUST CABLE TENSION See Fig TO REMOVE WHEELS See FigCARBURETOR ENGINE SPEEDSTORAGE OTHERFUEL SYSTEM ENGINE OILTROUBLESHOOTING Loss of powerDoes not start Engine idles orREPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES AUGER HOUSING / IMPELLER ASSEMBLY01.07.026-C 2 EXPLODEDPART DESCRIPTIONREPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES AUGER HOUSING / IMPELLER ASSEMBLYPART DESCRIPTIONREPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES CONTROL PANEL / DISCHARGE CHUTE 01.09.010-BREPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES HANDLES 01.10.019REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES HANDLES 01.08.002-F HANDLES 01.12.001-E42 EXPLODED REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES DRIVE01.02.013-A REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES DRIVE assy of 1a,1b AXLE ASSEMBLY CHASSIS / ENGINE / PULLEYS 423185X505ENGINE MOUNTING PLATE 428684REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES WHEELS WHEEL ASSEMBLY RHSAFETY IGNITION KEY REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES BAG OF PARTS193071 181037 DECALSDECAL, DANGER SERVICE NOTES SERVICE NOTES LIMITED WARRANTY