Poulan 430355, 96192003302 owner manual Operation, Meets A.N.S.I. Safety Requirements

Page 8

MEETS A.N.S.I. SAFETY REQUIREMENTS

OPERATION

GASOLINE

FILLER CAP

MUFFLER

CHOKE CON-

TROL

PRIMER

SAFETY

	AUGER	DISCHARGE CHUTE
ELECTRIC	AUGER	CONTROL LEVER
ELECTRIC	CONTROL	CONTROL LEVER
START BUTTON	CONTROL
START BUTTON	LEVER	DRIVE SPEED
	LEVER	DRIVE SPEED
RECOIL		CONTROL LEVER	TRACTION
RECOIL			TRACTION
(AUXILIARY)			DRIVE
STARTER			CONTROL
HANDLE			LEVER
	CHUTE
DEFLECTOR
			LIGHT

IGNITION

KEYON / OFF SWITCH

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY VARY

WITH THE ENGINE

ON YOUR UNIT.

AUGERS

DISCHARGE

CHUTE

CLEAN-OUT TOOL

FIG. 8

CHUTE DEFLECTOR KNOB

HANDLE

KNOB

MUFFLER

TOOLBOX

SKID PLATE

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button - used for starting the engine.

Recoil (auxiliary) starter handle - used for starting the engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

Choke control - used for starting a cold engine. ON / OFF switch - used to STOP the engine.

Drive speed control lever - used to select forward or reverse motion and speed of snow thrower.

Traction drive control lever - used to engage power- propelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the direc- tion the snow is thrown.

Skid plate - used to adjust height of scraper bar from the ground.

8

Image 8

Contents OWNERS MANUAL MODEL NUMBER SNOW THROWERIMPORTANT MANUAL XT824ESSafe Operation Practices for Walk-Behind Snow Throwers TrainingPreparation OperationTABLE OF CONTENTS PRODUCT SPECIFICATIONSMaintenance and Storage CUSTOMER RESPONSIBILITIESASSEMBLY / PRE-OPERATION HOW TO SET UP YOUR SNOW THROWERPARTS PACKED SEPARATELY IN CARTON REMOVE SNOW THROWER FROM CARTONUNFOLD UPPER HANDLE INSTALL SPEED CONTROL ROD See Figs. 1 andINSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and CHECK TIRE PRESSURE INSTALL AUGER CONTROL ROD See Figs. 5 andINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD See Fig OPERATION KNOW YOUR SNOW THROWERMEETS A.N.S.I. SAFETY REQUIREMENTS Recoil auxiliary starter handle - used for starting the engineHOW TO USE YOUR SNOW THROWER STOPPINGTO USE CHOKE CONTROL See Fig TO CONTROL SNOW DISCHARGE See FigsUSING THE CLEAN-OUT TOOL See Fig TO THROW SNOW See FigTO MOVE FORWARD AND BACKWARD See Fig AUGER CONTROL LEVERBEFORE STARTING THE ENGINE TO ADJUST SKID PLATES See FigSCRAPER BAR See Fig CHECK ENGINE OIL LEVEL See FigSNOW THROWING TIPS TO START ENGINEBEFORE STOPPING IF RECOIL STARTER HAS FROZENMAINTENANCE LUBRICATION CHARTGENERAL RECOMMENDATIONS BEFORE EACH USECLEANING ENGINEAUGER GEAR CASE TRACTION DRIVE SYSTEMSERVICE AND ADJUSTMENTS 1. Be sure the on/off switch is in the OFF position2. Remove safety ignition key TO ADJUST SNOW THROWER HEIGHTTO REPLACE BELTS See Fig TO ADJUST CABLE TENSION See Fig TO REMOVE WHEELS See FigCARBURETOR ENGINE SPEEDSTORAGE OTHERFUEL SYSTEM ENGINE OILTROUBLESHOOTING Loss of powerDoes not start Engine idles orREPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES AUGER HOUSING / IMPELLER ASSEMBLY01.07.026-C 2 EXPLODEDPART DESCRIPTIONREPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES AUGER HOUSING / IMPELLER ASSEMBLYPART DESCRIPTIONREPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES CONTROL PANEL / DISCHARGE CHUTE 01.09.010-BREPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES HANDLES 01.10.019REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES HANDLES 01.08.002-F HANDLES 01.12.001-E01.02.013-A REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES DRIVE42 EXPLODED REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES DRIVE assy of 1a,1b AXLE ASSEMBLY CHASSIS / ENGINE / PULLEYS 423185X505ENGINE MOUNTING PLATE 428684REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES WHEELS WHEEL ASSEMBLY RH193071 REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES BAG OF PARTSSAFETY IGNITION KEY DECAL, DANGER DECALS181037 SERVICE NOTES SERVICE NOTES LIMITED WARRANTY