Poulan 96192003302 Handles, REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES, Part, Description

Page 29

REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES (96192003302)

HANDLES

		KEY	PART
		NO.	NO.	DESCRIPTION
		1	180480	IMPELLER ROD ASSEMBLY
		2	405740	TRACTION ROD ASSEMBLY
		3	180445	SHIFTER ROD TOP
		4	187716	SHIFTER ROD BOTTOM
10		5	180447	SPRING SLEEVE
10		6	178669	IMPELLER SPRING
		6	178669	IMPELLER SPRING
1	3	7	180926	TRACTION SPRING
1		8	72270505	CARRIAGE BOLT 5/16-18 X .75
		9	155377	NUT 5/16-18
		10	169675	RETAINER
		8
	9
	4
		5

10	7

01.12.001-E

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Image 29

Contents SNOW THROWER OWNERS MANUAL MODEL NUMBERIMPORTANT MANUAL XT824ESTraining Safe Operation Practices for Walk-Behind Snow ThrowersPreparation OperationPRODUCT SPECIFICATIONS TABLE OF CONTENTSMaintenance and Storage CUSTOMER RESPONSIBILITIESHOW TO SET UP YOUR SNOW THROWER ASSEMBLY / PRE-OPERATIONPARTS PACKED SEPARATELY IN CARTON REMOVE SNOW THROWER FROM CARTONUNFOLD UPPER HANDLE INSTALL SPEED CONTROL ROD See Figs. 1 andINSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and CHECK TIRE PRESSURE INSTALL AUGER CONTROL ROD See Figs. 5 andINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD See Fig KNOW YOUR SNOW THROWER OPERATIONRecoil auxiliary starter handle - used for starting the engine MEETS A.N.S.I. SAFETY REQUIREMENTSSTOPPING HOW TO USE YOUR SNOW THROWERTO USE CHOKE CONTROL See Fig TO CONTROL SNOW DISCHARGE See FigsTO THROW SNOW See Fig USING THE CLEAN-OUT TOOL See FigTO MOVE FORWARD AND BACKWARD See Fig AUGER CONTROL LEVERTO ADJUST SKID PLATES See Fig BEFORE STARTING THE ENGINESCRAPER BAR See Fig CHECK ENGINE OIL LEVEL See FigTO START ENGINE SNOW THROWING TIPSBEFORE STOPPING IF RECOIL STARTER HAS FROZENLUBRICATION CHART MAINTENANCEGENERAL RECOMMENDATIONS BEFORE EACH USEENGINE CLEANINGAUGER GEAR CASE TRACTION DRIVE SYSTEM1. Be sure the on/off switch is in the OFF position SERVICE AND ADJUSTMENTS2. Remove safety ignition key TO ADJUST SNOW THROWER HEIGHTTO REPLACE BELTS See Fig TO REMOVE WHEELS See Fig TO ADJUST CABLE TENSION See FigCARBURETOR ENGINE SPEEDOTHER STORAGEFUEL SYSTEM ENGINE OILLoss of power TROUBLESHOOTINGDoes not start Engine idles orAUGER HOUSING / IMPELLER ASSEMBLY REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES01.07.026-C 2 EXPLODEDDESCRIPTION PARTAUGER HOUSING / IMPELLER ASSEMBLY REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ESPART DESCRIPTIONAUGER HOUSING / IMPELLER ASSEMBLY 01.09.010-B CONTROL PANEL / DISCHARGE CHUTECONTROL PANEL / DISCHARGE CHUTE 01.10.019 REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES HANDLESPART 01.08.002-F 01.12.001-E HANDLES01.02.013-A REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES DRIVE42 EXPLODED PART assy of 1a,1b AXLE ASSEMBLY 423185X505 CHASSIS / ENGINE / PULLEYSENGINE MOUNTING PLATE 428684CHASSIS / ENGINE / PULLEYS WHEEL ASSEMBLY RH REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES WHEELS193071 REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES BAG OF PARTSSAFETY IGNITION KEY DECAL, DANGER DECALS181037 SERVICE NOTES SERVICE NOTES LIMITED WARRANTY