Poulan 96192003302, 430355 REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES, Part, Description

Page 23

REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES (96192003302)

AUGER HOUSING / IMPELLER ASSEMBLY

2	KEY	PART
2	NO.	NO.	DESCRIPTION
	NO.	NO.	DESCRIPTION
	1	420493X479	AUGER ASSEMBLY LH 24
1	2	420494X479	AUGER ASSEMBLY RH 24
1

01.07.017-A

			4
				2
		4
		KEY	PART
		NO.	NO.	DESCRIPTION
		1	174762X479	SKID PLATE LH
		2	178777X479	SKID PLATE RH
		3	72270506	CARRIAGE BOLT 5/16−18 X .75
		4	751153	NUT 5/16−18
3	01.11.001-A	1
3		1

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 23

Image 23

Contents XT824ES OWNERS MANUAL MODEL NUMBERSNOW THROWER IMPORTANT MANUALOperation Safe Operation Practices for Walk-Behind Snow ThrowersTraining PreparationCUSTOMER RESPONSIBILITIES TABLE OF CONTENTSPRODUCT SPECIFICATIONS Maintenance and StorageREMOVE SNOW THROWER FROM CARTON ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER PARTS PACKED SEPARATELY IN CARTONUNFOLD UPPER HANDLE INSTALL SPEED CONTROL ROD See Figs. 1 andINSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and CHECK TIRE PRESSURE INSTALL AUGER CONTROL ROD See Figs. 5 andINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD See Fig KNOW YOUR SNOW THROWER OPERATIONRecoil auxiliary starter handle - used for starting the engine MEETS A.N.S.I. SAFETY REQUIREMENTSTO CONTROL SNOW DISCHARGE See Figs HOW TO USE YOUR SNOW THROWERSTOPPING TO USE CHOKE CONTROL See FigAUGER CONTROL LEVER USING THE CLEAN-OUT TOOL See FigTO THROW SNOW See Fig TO MOVE FORWARD AND BACKWARD See FigCHECK ENGINE OIL LEVEL See Fig BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig SCRAPER BAR See FigIF RECOIL STARTER HAS FROZEN SNOW THROWING TIPSTO START ENGINE BEFORE STOPPINGBEFORE EACH USE MAINTENANCELUBRICATION CHART GENERAL RECOMMENDATIONSTRACTION DRIVE SYSTEM CLEANINGENGINE AUGER GEAR CASETO ADJUST SNOW THROWER HEIGHT SERVICE AND ADJUSTMENTS1. Be sure the on/off switch is in the OFF position 2. Remove safety ignition keyTO REPLACE BELTS See Fig ENGINE SPEED TO ADJUST CABLE TENSION See FigTO REMOVE WHEELS See Fig CARBURETORENGINE OIL STORAGEOTHER FUEL SYSTEMEngine idles or TROUBLESHOOTINGLoss of power Does not start2 EXPLODED REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ESAUGER HOUSING / IMPELLER ASSEMBLY 01.07.026-CDESCRIPTION PARTDESCRIPTION REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ESAUGER HOUSING / IMPELLER ASSEMBLY PARTDESCRIPTION 01.09.010-B CONTROL PANEL / DISCHARGE CHUTEDESCRIPTION 01.10.019 REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES HANDLESPART 01.08.002-F 01.12.001-E HANDLES01.02.013-A REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES DRIVE42 EXPLODED DESCRIPTION assy of 1a,1b AXLE ASSEMBLY 428684 CHASSIS / ENGINE / PULLEYS423185X505 ENGINE MOUNTING PLATEPART WHEEL ASSEMBLY RH REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES WHEELS193071 REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES BAG OF PARTSSAFETY IGNITION KEY DECAL, DANGER DECALS181037 SERVICE NOTES SERVICE NOTES LIMITED WARRANTY