Craftsman 536.88123 To Throw Snow, To USE Wheel Lockout PIN, Before Starting the Engine

Page 11

•Engagethe traction drive lever as shown in next figure, left hand. As the snow thrower starts to move, maintain a firm

hold on the handles, and guide the snow thrower along the cteadng path. Do not attempt to push the snow thrower.

•To move the snow thrower backward, move the speed shifter lever into first or second reverse and engage the traction drive lever (left hand).

IMPORTANT: Never move the speed shifter lever while the traction lever is down.

TO THROW SNOW

•Push down the auger drive lever, see fig- ure below, release to stop throwing snow.

TractionDrive Lever Auger Drive Lever

Left hand

t

/ Righthand

TO USE WHEEL LOCKOUT PIN

•The left hand wheel is secured to the axle with a klick pin, see figure below. This unit was shipped with this klick pin in the locked position (klick pin through hole in wheel).

!-Wheel Drive

Locked

__Position

K'ick Pin/ I_1_1

BEFORE STARTING THE ENGINE

•tf the snow thrower must be moved with- out the aid of the engine, it is easier to pull the snow thrower by the handles rather than pushing.

•Before you service or start the engine, fa- miliarize yourself with the snow thrower.

Be sure you understand the function and location of all controls.

NOTE: Check tension of clutch cables be-

fore starting the engine (See To Adjust The Control Cables paragraph on page 19).

•

Be sure that

all fasteners are tight.

 

 

•

Make sure the height adjust skids are

 

 

 

properly adjusted (See To Adjust Skid

 

I

 

Height paragraph on page 18).

 

• Checktire pressure (14 to 17 pounds).

 

See side of tire for maximum inflation. Do

 

not exceed listed maximum pressure.

 

CHECKTHE

OIL

 

NOTE: The engine was shipped from the

 

factory filled with oil. Check the level of the

oil. Add oil as needed,

 

•

Make sure the unit is level.

 

 

NOTE: Do not check the level of the oil

 

while the engine runs.

 

•

Remove the oil fill cap/dipstick. Check

the

 

 

oil.

 

 

 

_Oil Fill/Dipstick

tL

;,_,.,'

NOTE: Oil level must be

._)

between full and add

 

mark.

•For ease of maneuverability in light snow conditions, disconnect the klick pin from the wheel locked position and push into

the single wheel drive position (klick pin through axle hole only), see figure below. NOTE: Make sure that the klick pin is in the

single wheel drive position, through axle only and not through the hole in wheel.

Klick Pin_

SingleWheel Drive

•If necessary, add oil until the oil reaches the FULL mark on the oil fill cap/dipstick

(see figure above). Do not add too much oil.

•Tighten the fill cap/dipstick securely each time you check the oil level.

NOTE: For extreme cold operating condi- tions of 0°F and below, use a partial synthetic 0W30 motor oil for easier starting.

NOTE: S.A.E. 5W30 motor oil may be used to make starting easier in areas where tem- perature is consistently 20°F or lower.

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Snow Thrower Training Contents Service and Adjustments 18-22 Warranty StorageLimited TWO-YEAR Warranty on Craftsman Snow Thrower Operation Preparation8-16 Hex Jam Nuts Maintenance and StorageSteep sloping surfaces. do not USE Snow Thrower on Surfaces FlatwasherSpeed Lever Tools Required for AssemblyGlasses or eye shields while assembling snow thrower To Installthe Upper Handle and Crankassembly HOW to SET UP Your Snow ThrowerSpeed Selector ROD AssembleReplace carriage bolt Headlight Remote Chute Control KnobChute Chute Deflector Deflector Know Your Snow ThrowerTo Stopyour Snowthrower Howto Useyour Snow ThrowerTo Control Snow Discharge To Move Forward BackwardCheckthe OIL To Throw SnowTo USE Wheel Lockout PIN Before Starting the EngineCold Start Fill GASBe sure the auger drive and traction drive Warm StartPush down on the starter button until To Start Engine Recoil StarterFor maximum snow thrower efficiency Frozen Recoil StarterSnow Throwing Tips Gages. Then continue with the directions for cold startLubrication Chart Customer Responsibilities Service Schedule Dates RecordsAfter Each USE Lubrication Every 10 HoursLubrication Before Storage Snow Thrower After First USESpark Plug LubricationOIL Recommendation Engine LubricationTo Adjustthe Clutch Control Cables To Adjust Skid HeightTo Adjust Scraper BAR Traction Drive Belt To Adjust BeltsTo Replace Belts Auger Drive BeltTo Adjust the Friction Wheel To Adjustthe Belt GuideReplace bottom panel To Replace Friction WheelAuger End nutsTo Replace Auger Shear Bolt To Adjust or Replace Spark PlugTo Adjust Carburetor To AdjustSteps below Snow Thrower StorageEngine Storage OtherCorrection Trouble Cause

536.88123 specifications

The Craftsman 536.88123 is a powerful and versatile snow blower designed to tackle the toughest winter weather conditions. With its robust construction and advanced features, this machine is engineered for homeowners who desire efficiency and reliability in snow removal.

One of the standout features of the Craftsman 536.88123 is its impressive 27-inch clearing width. This wide path allows users to cover large areas quickly, making it suitable for both residential driveways and sidewalks. The snow blower is equipped with a strong and efficient 2-stage auger system that not only breaks up compact snow but also throws it far away from the cleared area. This ensures that snow is efficiently removed without simply pushing it aside, which can cause buildup over time.

Another significant characteristic of this model is its powerful 357cc engine, delivering substantial torque and performance. This engine is designed to handle heavy, wet snow with ease, providing users with the confidence to tackle even the most challenging conditions. The electric start feature adds convenience for those cold, winter mornings, allowing for easy ignition without the need for strenuous pulling.

The Craftsman 536.88123 is also designed for user comfort and ease of operation. The adjustable handle ensures a comfortable grip, and it can be modified to fit the user’s height. This snow blower features six forward and two reverse speeds, giving users full control over their snow clearing experience. The durable, rubber-edged auger not only provides efficient snow removal but also protects surfaces underneath, minimizing the risk of damage.

Additionally, the snow blower comes with a remote chute control system, allowing users to easily direct the snow discharge without having to manually adjust the chute. This feature is particularly beneficial for users who need to navigate around obstacles while working.

In terms of durability, the Craftsman 536.88123 is built with high-quality materials designed to withstand harsh conditions, ensuring longevity and dependable performance year after year.

With its combination of power, efficiency, and user-friendly design, the Craftsman 536.88123 is a top choice for those looking for a reliable solution to winter snow challenges. Whether you're clearing your driveway, sidewalk, or patio, this snow blower promises to make your winter maintenance tasks manageable and less labor-intensive.
Top Page Image Contents