Craftsman 536.88123 operating instructions To Adjust Skid Height, To Adjust Scraper BAR

Page 18

Z_ CAUTION: Always disconnect the

spark plug wire and tie back away from the plug before making any adjustments or repairs.

TO ADJUST SKID HEIGHT

This snow thrower is equipped with two height adjustment skids, located on the out- side of the auger housing (see figure be- low). These skids elevate the front of the snow thrower.

Height Adjust Skids

Skid Mounting

For normal hard surfaces, adjust the skids as follows:

•Check tire pressure (14 pounds). See side of tire for maximum inflation. Do not exceed maximum pressure on side of tire.

•Place the extra shear bolts supplied (found in parts bag) under each end of the scraper bar near but not under the skid.

•Loosen the skid mounting nuts (see fig- ure above) and adjust the skids up to bring the front of the snow thrower down.

•Re-tighten the mounting nuts.

•Set the skid on the other side at the same height.

For rocky or uneven surfaces, adjust the skids as follows:

•Raise the front of the snow thrower by moving the skids down. This will help pre- vent rocks and other debris from being picked up and thrown by the auger.

NOTE: Be sure that snow thrower is set at same height on both sides.

TO ADJUST SCRAPER BAR

After considerable use, the metal scraper

bar will have a definite wear pattern. The scraper bar in conjunction with the skids should always be adjusted to allow 1/8" be-

tween the scraper bar and the sidewalk or area to be cleaned. The scraper bar may have to be returned to its original lower set- ting to maintain the original performance level. To adjust:

•Position the snow threwer on a level sur- face.

•Make sure both tires are equally inflated.

•Loosen the carriage bolts and nuts secur- ing the scraper bar to the auger housing.

•Adjust the scraper bar to the proper posi- tion.

•Tighten the carriage bolts and nuts, mak- ing sure that the scraper bar is parallel with the working surface.

•For extended operation, the scraper bar may be reversed. If the scraper bar must be replaced due to wear, remove the car- riage bolts and nuts and install a new scraper bar.

/_. CAUTION: Be certain to maintain

proper ground clearance for your par- ticular area to be cleared. Objects such as

gravel, rocks or other debris, if struck by the impeller, may be thrown with sufficient force

to cause personal injury, property damage or damage to the snow thrower.

TO ADJUSTTHE CLUTCH CONTROL

CABLES

Periodic adjustment of the cables may be required due to normal stretch and wear on

the belts. To check for correct adjustment, disconnect "Z" Fitting at clutch lever, move clutch lever to the full forward position, just contacting the plastic bumper. The control cables are correctly adjusted when the cen- ter of the "Z" fitting is between the center and top of the hole and there is no droop in the cable (see figure below). If adjustment is necessary:

Control Lever must be in full

Aug

"Z" Fitting

when checking

Plastic Bumper

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Snow Thrower Contents Service and Adjustments 18-22 Warranty Storage Limited TWO-YEAR Warranty on Craftsman Snow ThrowerTraining Preparation OperationFlatwasher Maintenance and StorageSteep sloping surfaces. do not USE Snow Thrower on Surfaces 8-16 Hex Jam NutsTools Required for Assembly Glasses or eye shields while assembling snow throwerSpeed Lever HOW to SET UP Your Snow Thrower To Installthe Upper Handle and CrankassemblyAssemble Replace carriage boltSpeed Selector ROD Remote Chute Control Knob HeadlightKnow Your Snow Thrower Chute Chute Deflector DeflectorTo Move Forward Backward Howto Useyour Snow ThrowerTo Control Snow Discharge To Stopyour SnowthrowerBefore Starting the Engine To Throw SnowTo USE Wheel Lockout PIN Checkthe OILFill GAS Cold StartTo Start Engine Recoil Starter Warm StartPush down on the starter button until Be sure the auger drive and traction driveGages. Then continue with the directions for cold start Frozen Recoil StarterSnow Throwing Tips For maximum snow thrower efficiencyCustomer Responsibilities Service Schedule Dates Records Lubrication ChartSnow Thrower After First USE Lubrication Every 10 HoursLubrication Before Storage After Each USEEngine Lubrication LubricationOIL Recommendation Spark PlugTo Adjust Skid Height To Adjust Scraper BARTo Adjustthe Clutch Control Cables Auger Drive Belt To Adjust BeltsTo Replace Belts Traction Drive BeltTo Adjustthe Belt Guide To Adjust the Friction WheelEnd nuts To Replace Friction WheelAuger Replace bottom panelTo Adjust To Adjust or Replace Spark PlugTo Adjust Carburetor To Replace Auger Shear BoltOther Snow Thrower StorageEngine Storage Steps belowTrouble Cause Correction

536.88123 specifications

The Craftsman 536.88123 is a powerful and versatile snow blower designed to tackle the toughest winter weather conditions. With its robust construction and advanced features, this machine is engineered for homeowners who desire efficiency and reliability in snow removal.

One of the standout features of the Craftsman 536.88123 is its impressive 27-inch clearing width. This wide path allows users to cover large areas quickly, making it suitable for both residential driveways and sidewalks. The snow blower is equipped with a strong and efficient 2-stage auger system that not only breaks up compact snow but also throws it far away from the cleared area. This ensures that snow is efficiently removed without simply pushing it aside, which can cause buildup over time.

Another significant characteristic of this model is its powerful 357cc engine, delivering substantial torque and performance. This engine is designed to handle heavy, wet snow with ease, providing users with the confidence to tackle even the most challenging conditions. The electric start feature adds convenience for those cold, winter mornings, allowing for easy ignition without the need for strenuous pulling.

The Craftsman 536.88123 is also designed for user comfort and ease of operation. The adjustable handle ensures a comfortable grip, and it can be modified to fit the user’s height. This snow blower features six forward and two reverse speeds, giving users full control over their snow clearing experience. The durable, rubber-edged auger not only provides efficient snow removal but also protects surfaces underneath, minimizing the risk of damage.

Additionally, the snow blower comes with a remote chute control system, allowing users to easily direct the snow discharge without having to manually adjust the chute. This feature is particularly beneficial for users who need to navigate around obstacles while working.

In terms of durability, the Craftsman 536.88123 is built with high-quality materials designed to withstand harsh conditions, ensuring longevity and dependable performance year after year.

With its combination of power, efficiency, and user-friendly design, the Craftsman 536.88123 is a top choice for those looking for a reliable solution to winter snow challenges. Whether you're clearing your driveway, sidewalk, or patio, this snow blower promises to make your winter maintenance tasks manageable and less labor-intensive.
Top Page Image Contents