Craftsman 536.88123 operating instructions Warm Start, Push down on the starter button until

Page 13

•Connect the power cord to the switch box on the engine.

•Plug the other end of the power cord into a three-hole, grounded 120 volt A.C. receptacle.

•Push the primer button while covedng the vent hole as follows: (Remove finger from primer button between primes). See figure on page 9 for location.

One time if temperature is above 50°F.

Two times if temperature is 50°F to 15°F. Four times if temperature is below 15°F.

•Push down on the starter button until the

engine starts. Do not crank for more than 10 seconds at a time. This electdc starter

is thermally protected. If overheated it will stop automatically and can be restarted only when it has cooled to a safe temperature (a wait of about 5 to 10 minutes is required).

•When the engine starts, release the starter button and move choke lever to "1/2 choke" position. When engine runs

smoothly, move choke lever to =No Choke" Position.

•Disconnect the power cord from the receptacle first and then from the switch box on engine.

NOTE: Allow the engine to warm up for several minutes before blowing snow in temperatures below 0°F.

•Run the engine at full throttle "_ (FAST) when throwing snow.

TO START ENGINE (Recoil Starter)

Be sure that the engine has sufficient oil. The snow thrower engine is equipped with a

recoil starter. Before starting the engine, be certain that you have read the following in- formation:

COLD START

•Be sure the auger drive and traction drive

levers are in the disengaged (released) position.

•Move the throttle control to 4_ (FAST)

position. See figure on page 9 for loca- tion.

•Remove the keys from the plastic bag. In- sert one key into the ignition slot. Be sure it snaps into place. DO NOT TURN KEY. Keep the second key in a safe place.

•Rotate the choke knob to H choke ON position. See figure on page 9.

•Push the primer button, see figure on page 9, while covering the vent hole as follows: (Remove finger from primer but- ton between primes).

One time if temperature is above 50°F.

Two times if temperature is 50°F to 15°F.

Four times if temperature is below 15°E

•Pull the recoil starter handle rapidly.Do not allow the handle to snap back, but al-

low it to rewind slowly while keeping a firm hold on the starter handle.

•As engine starts warms up move choke lever to "1/2 choke" position. When engine

runs smoothly, move choke lever to =No

Choke" Position.

NOTE: Allow the engine to warm up for several minutes before blowing snow in tem- peratures below 0°F.

•Run the engine at full throttle ,_ (FAST) when throwing snow.

WARM START

If restarting a warm engine after a short shutdown, leave choke at (OFF) and do not

push the primer button, tf the engine fails to start, follow the Cold Start Instructions on

page 13.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Snow Thrower Limited TWO-YEAR Warranty on Craftsman Snow Thrower Contents Service and Adjustments 18-22 Warranty StorageTraining Operation PreparationSteep sloping surfaces. do not USE Snow Thrower on Surfaces Maintenance and StorageFlatwasher 8-16 Hex Jam NutsGlasses or eye shields while assembling snow thrower Tools Required for AssemblySpeed Lever To Installthe Upper Handle and Crankassembly HOW to SET UP Your Snow ThrowerReplace carriage bolt AssembleSpeed Selector ROD Headlight Remote Chute Control KnobChute Chute Deflector Deflector Know Your Snow ThrowerTo Control Snow Discharge Howto Useyour Snow ThrowerTo Move Forward Backward To Stopyour SnowthrowerTo USE Wheel Lockout PIN To Throw SnowBefore Starting the Engine Checkthe OILCold Start Fill GASPush down on the starter button until Warm StartTo Start Engine Recoil Starter Be sure the auger drive and traction driveSnow Throwing Tips Frozen Recoil StarterGages. Then continue with the directions for cold start For maximum snow thrower efficiencyLubrication Chart Customer Responsibilities Service Schedule Dates RecordsLubrication Before Storage Lubrication Every 10 HoursSnow Thrower After First USE After Each USEOIL Recommendation LubricationEngine Lubrication Spark PlugTo Adjust Scraper BAR To Adjust Skid HeightTo Adjustthe Clutch Control Cables To Replace Belts To Adjust BeltsAuger Drive Belt Traction Drive BeltTo Adjust the Friction Wheel To Adjustthe Belt GuideAuger To Replace Friction WheelEnd nuts Replace bottom panelTo Adjust Carburetor To Adjust or Replace Spark PlugTo Adjust To Replace Auger Shear BoltEngine Storage Snow Thrower StorageOther Steps belowCorrection Trouble Cause

536.88123 specifications

The Craftsman 536.88123 is a powerful and versatile snow blower designed to tackle the toughest winter weather conditions. With its robust construction and advanced features, this machine is engineered for homeowners who desire efficiency and reliability in snow removal.

One of the standout features of the Craftsman 536.88123 is its impressive 27-inch clearing width. This wide path allows users to cover large areas quickly, making it suitable for both residential driveways and sidewalks. The snow blower is equipped with a strong and efficient 2-stage auger system that not only breaks up compact snow but also throws it far away from the cleared area. This ensures that snow is efficiently removed without simply pushing it aside, which can cause buildup over time.

Another significant characteristic of this model is its powerful 357cc engine, delivering substantial torque and performance. This engine is designed to handle heavy, wet snow with ease, providing users with the confidence to tackle even the most challenging conditions. The electric start feature adds convenience for those cold, winter mornings, allowing for easy ignition without the need for strenuous pulling.

The Craftsman 536.88123 is also designed for user comfort and ease of operation. The adjustable handle ensures a comfortable grip, and it can be modified to fit the user’s height. This snow blower features six forward and two reverse speeds, giving users full control over their snow clearing experience. The durable, rubber-edged auger not only provides efficient snow removal but also protects surfaces underneath, minimizing the risk of damage.

Additionally, the snow blower comes with a remote chute control system, allowing users to easily direct the snow discharge without having to manually adjust the chute. This feature is particularly beneficial for users who need to navigate around obstacles while working.

In terms of durability, the Craftsman 536.88123 is built with high-quality materials designed to withstand harsh conditions, ensuring longevity and dependable performance year after year.

With its combination of power, efficiency, and user-friendly design, the Craftsman 536.88123 is a top choice for those looking for a reliable solution to winter snow challenges. Whether you're clearing your driveway, sidewalk, or patio, this snow blower promises to make your winter maintenance tasks manageable and less labor-intensive.
Top Page Image Contents