Craftsman 536.88123 operating instructions OIL Recommendation, Engine Lubrication, Spark Plug

Page 17

LUBRICATION

• Hex Shaft and Gears - Hex shaft and

gears require no lubrication. All bearings and bushings are lifetime lubricated and require no maintenance.

NOTE: Any greasing or oiling of the above components can cause contamination of the friction wheel. If the disc drive plate or friction wheel comes in contact with grease

or oil, damage to the friction wheel will re- sult.

Should grease or oil come in contact with

the disc drive plate or friction wheel, be sure

to clean the plate and wheel thoroughly.

NOTE: For storage, the hex shaft and gears should be wiped with 5W-30 motor oil to prevent rusting. See second figure on page 15.

•Auger Gear Box - The auger gear box is lubricated at the factory and should not

require additional lubrication. If for some reason the lubricant should leak out, or if

the auger gear box has been serviced,

add Lubriplate No. 630-AA or equivalent.

Maximum 3-1/4 ounces should be used.

Remove filler plug as seen in figure below once a year. If grease is visible, do not add. If grease is not visible, use a piece of fine wire like a dipstick, to check if there is grease in the gearbox. Add grease if necessary. Reinstall gear box filler.

OIL RECOMMENDATION

Only use high quality detergent oit rated with AP_ service classification SG. Select

the oil'sviscosity grade according to your expected operating temperature:

NOTE: For extreme cold operating condi- tions of 0° and below, use a partial synthetic 0W30 motor oil for easier starting.

Change the oil every twenty-five (25) hours thereafter, and at the beginning of each season.

•Position the snow thrower so that the oil drain plug is at the lowest point on the engine. Remove the oil drain plug and the oil fill cap/dipstick. Drain the oil into a suitable container. Oil will drain more freely when warm.

•Replace the oil drain plug and tighten se- curely.

SPARK PLUG

Make sure that the spark plug is tight- ened securely into the engine and the spark plug wire is attached to the spark plug.

If a torque wrench is available, torque plug to 18 to 23 foot pounds.

Clean the area around the spark plug base before removal to prevent dirt from entering the engine.

Clean the spark plug and reset the gap periodically at .030 inch.

Gear Box Filler

Plug

ENGINE

LUBRICATION

Check the crankcase oil level (see figure be-

low) before starting the engine and after each five (5) hours of continuous use. Add

S.A.E. 5W30 motor oil as needed. Tighten

fill cap/dipstick securely each time you check the oil level.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Training Contents Service and Adjustments 18-22 Warranty StorageLimited TWO-YEAR Warranty on Craftsman Snow Thrower Operation PreparationSteep sloping surfaces. do not USE Snow Thrower on Surfaces Maintenance and StorageFlatwasher 8-16 Hex Jam NutsSpeed Lever Tools Required for AssemblyGlasses or eye shields while assembling snow thrower To Installthe Upper Handle and Crankassembly HOW to SET UP Your Snow ThrowerSpeed Selector ROD AssembleReplace carriage bolt Headlight Remote Chute Control KnobChute Chute Deflector Deflector Know Your Snow ThrowerTo Control Snow Discharge Howto Useyour Snow ThrowerTo Move Forward Backward To Stopyour SnowthrowerTo USE Wheel Lockout PIN To Throw SnowBefore Starting the Engine Checkthe OILCold Start Fill GASPush down on the starter button until Warm StartTo Start Engine Recoil Starter Be sure the auger drive and traction driveSnow Throwing Tips Frozen Recoil StarterGages. Then continue with the directions for cold start For maximum snow thrower efficiencyLubrication Chart Customer Responsibilities Service Schedule Dates RecordsLubrication Before Storage Lubrication Every 10 HoursSnow Thrower After First USE After Each USEOIL Recommendation LubricationEngine Lubrication Spark PlugTo Adjustthe Clutch Control Cables To Adjust Skid HeightTo Adjust Scraper BAR To Replace Belts To Adjust BeltsAuger Drive Belt Traction Drive BeltTo Adjust the Friction Wheel To Adjustthe Belt GuideAuger To Replace Friction WheelEnd nuts Replace bottom panelTo Adjust Carburetor To Adjust or Replace Spark PlugTo Adjust To Replace Auger Shear BoltEngine Storage Snow Thrower StorageOther Steps belowCorrection Trouble Cause

536.88123 specifications

The Craftsman 536.88123 is a powerful and versatile snow blower designed to tackle the toughest winter weather conditions. With its robust construction and advanced features, this machine is engineered for homeowners who desire efficiency and reliability in snow removal.

One of the standout features of the Craftsman 536.88123 is its impressive 27-inch clearing width. This wide path allows users to cover large areas quickly, making it suitable for both residential driveways and sidewalks. The snow blower is equipped with a strong and efficient 2-stage auger system that not only breaks up compact snow but also throws it far away from the cleared area. This ensures that snow is efficiently removed without simply pushing it aside, which can cause buildup over time.

Another significant characteristic of this model is its powerful 357cc engine, delivering substantial torque and performance. This engine is designed to handle heavy, wet snow with ease, providing users with the confidence to tackle even the most challenging conditions. The electric start feature adds convenience for those cold, winter mornings, allowing for easy ignition without the need for strenuous pulling.

The Craftsman 536.88123 is also designed for user comfort and ease of operation. The adjustable handle ensures a comfortable grip, and it can be modified to fit the user’s height. This snow blower features six forward and two reverse speeds, giving users full control over their snow clearing experience. The durable, rubber-edged auger not only provides efficient snow removal but also protects surfaces underneath, minimizing the risk of damage.

Additionally, the snow blower comes with a remote chute control system, allowing users to easily direct the snow discharge without having to manually adjust the chute. This feature is particularly beneficial for users who need to navigate around obstacles while working.

In terms of durability, the Craftsman 536.88123 is built with high-quality materials designed to withstand harsh conditions, ensuring longevity and dependable performance year after year.

With its combination of power, efficiency, and user-friendly design, the Craftsman 536.88123 is a top choice for those looking for a reliable solution to winter snow challenges. Whether you're clearing your driveway, sidewalk, or patio, this snow blower promises to make your winter maintenance tasks manageable and less labor-intensive.
Top Page Image Contents