Craftsman 536.88123 Lubrication Every 10 Hours, Lubrication Before Storage, After Each USE

Page 16

SNOW THROWER

AFTER FIRST USE

•Check for any loose or damaged parts after each use.

•Tighten any loose fasteners,

•Check and maintain the auger.

AFTER EACH USE

•Remove all snow and slush off the snow

thrower to prevent freezing of auger or controls.

•Check controls to make sure they are functioning properly.

•If any parts are worn or damaged, replace immediately.

SNOW THROWER

LUBRICATION - EVERY 10 HOURS

•Auger Shaft - Using a hand grease gun, lubricate the auger shaft zerk fittings (See figure below) every ten (10) operating hours. Each time a shear bolt is replaced (See To Replace Auger Shear Bolt on page 22), the auger shaft MUST be greased.

•For storage or when replacing shear bolts, remove shear bolts and lubricate

auger shaft zerks. Rotate augers several times on the shaft and reinstall the shear bolts.

•See Lubrication Chart diagram on page 15 for lubrication points and type of lubri- cant.

LUBRICATION - EVERY 25 HOURS

•Lubricate Disc Drive Plate every twenty- five (25) hours and at the end of the sea- son and/or before storage.

To Lubricate:

•Position speed selector lever in first gear.

•Stand the snow thrower up on the auger housing end.

Friction

Wheel

(Require

Plate

 

No

 

Lubrication)

 

Friction

Wheel

Beadng

between tdction

 

wheel

and disc drive

grease

Place

coin in gap

should be visible

plate

 

[_]_3--Grease Zerk

•Remove the bottom panel (see second figure on page 20).

•Turn disc drive plate clockwise by hand

until grease zerk is clearly visible at front center. See figure above.

•Place a coin or (a shim of equal thiok- ness) between the rubber friction wheel and disc drive plate to prevent rubber fric- tion wheel contacting the drive disc.

•To grease zerk, use a hand grease gun, lubricate with a Hi Temp EP Moly grease

See inset of figure above. DO NOT over fill or allow grease to come in contact with the disc drive plate or friction wheel or damage will result. Fill zerk only until grease becomes visible below bearing as- sembly located under grease zerk see in- sert above.

IMPORTANT: Remove coin and ensure that

a gap exists between friction wheel and disc drive plate.

NOTE: Clean all excess grease found on friction disc hub.

CAUTION; Do not allow grease to contact friction wheel and disc drive plate.

LUBRICATION - BEFORE STORAGE

•Remove both wheels, grease (any auto- motive type grease) both axles, see figure below, and replace wheels. Do this at least once a year and/or prior to storage.

Axle

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Snow Thrower Limited TWO-YEAR Warranty on Craftsman Snow Thrower Contents Service and Adjustments 18-22 Warranty StorageTraining Preparation OperationMaintenance and Storage Steep sloping surfaces. do not USE Snow Thrower on SurfacesFlatwasher 8-16 Hex Jam NutsGlasses or eye shields while assembling snow thrower Tools Required for AssemblySpeed Lever HOW to SET UP Your Snow Thrower To Installthe Upper Handle and CrankassemblyReplace carriage bolt AssembleSpeed Selector ROD Remote Chute Control Knob HeadlightKnow Your Snow Thrower Chute Chute Deflector DeflectorHowto Useyour Snow Thrower To Control Snow DischargeTo Move Forward Backward To Stopyour SnowthrowerTo Throw Snow To USE Wheel Lockout PINBefore Starting the Engine Checkthe OILFill GAS Cold StartWarm Start Push down on the starter button untilTo Start Engine Recoil Starter Be sure the auger drive and traction driveFrozen Recoil Starter Snow Throwing TipsGages. Then continue with the directions for cold start For maximum snow thrower efficiencyCustomer Responsibilities Service Schedule Dates Records Lubrication ChartLubrication Every 10 Hours Lubrication Before StorageSnow Thrower After First USE After Each USELubrication OIL RecommendationEngine Lubrication Spark PlugTo Adjust Scraper BAR To Adjust Skid HeightTo Adjustthe Clutch Control Cables To Adjust Belts To Replace BeltsAuger Drive Belt Traction Drive BeltTo Adjustthe Belt Guide To Adjust the Friction WheelTo Replace Friction Wheel AugerEnd nuts Replace bottom panelTo Adjust or Replace Spark Plug To Adjust CarburetorTo Adjust To Replace Auger Shear BoltSnow Thrower Storage Engine StorageOther Steps belowTrouble Cause Correction

536.88123 specifications

The Craftsman 536.88123 is a powerful and versatile snow blower designed to tackle the toughest winter weather conditions. With its robust construction and advanced features, this machine is engineered for homeowners who desire efficiency and reliability in snow removal.

One of the standout features of the Craftsman 536.88123 is its impressive 27-inch clearing width. This wide path allows users to cover large areas quickly, making it suitable for both residential driveways and sidewalks. The snow blower is equipped with a strong and efficient 2-stage auger system that not only breaks up compact snow but also throws it far away from the cleared area. This ensures that snow is efficiently removed without simply pushing it aside, which can cause buildup over time.

Another significant characteristic of this model is its powerful 357cc engine, delivering substantial torque and performance. This engine is designed to handle heavy, wet snow with ease, providing users with the confidence to tackle even the most challenging conditions. The electric start feature adds convenience for those cold, winter mornings, allowing for easy ignition without the need for strenuous pulling.

The Craftsman 536.88123 is also designed for user comfort and ease of operation. The adjustable handle ensures a comfortable grip, and it can be modified to fit the user’s height. This snow blower features six forward and two reverse speeds, giving users full control over their snow clearing experience. The durable, rubber-edged auger not only provides efficient snow removal but also protects surfaces underneath, minimizing the risk of damage.

Additionally, the snow blower comes with a remote chute control system, allowing users to easily direct the snow discharge without having to manually adjust the chute. This feature is particularly beneficial for users who need to navigate around obstacles while working.

In terms of durability, the Craftsman 536.88123 is built with high-quality materials designed to withstand harsh conditions, ensuring longevity and dependable performance year after year.

With its combination of power, efficiency, and user-friendly design, the Craftsman 536.88123 is a top choice for those looking for a reliable solution to winter snow challenges. Whether you're clearing your driveway, sidewalk, or patio, this snow blower promises to make your winter maintenance tasks manageable and less labor-intensive.
Top Page Image Contents