Craftsman 536.88123 To Replace Auger Shear Bolt, To Adjust or Replace Spark Plug

Page 22

FdctionWheel

Bolt

Nut

TO REPLACE AUGER SHEAR BOLT

The augers are secured to the auger shaft with special bolts (see figure below) that are designed to break (to protect the machine) if an object becomes lodged in the auger housing. Use of a harder bolt will destroy the protection provided by the shear bolt.

IMPORTANT: To ensure safety and perfor- mance (evels, only originalequipment shear belts should be used.

TO ADJUST OR REPLACE

THE SPARK PLUG

NOTICE: This spark ignition system meets all requirements of the Canadian Interfer- ence-Causing Equipment Regulations.

NOTICE: This engine complies with all cur- rent Australian and New Zealand Umitaions

regarding electromagnetic interference.

If you have difficulty starting your snow thrower, you may need to adjust or replace the spark plug. Follow the instructions be- low.

Replace the spark plug if the electrodes are pitted or burned or if the pomelain is cracked.

TO ADJUST:

•Clean the spark plug by carefully scrap- ing the electrodes (do not sand blast or use a wire brush).

•Be sure the spark plug is clean and free of foreign material Check the electrodes gap (see figure below) with a wire feeler gauge and reset the gap to .030 inch if necessary.

'-: I_

I :

Locknut=_ E_

•To replace a broken shear bolt, proceed as follows:

•Move the throttle to O (STOP) and turn off all controls.

•Disconnect the spark plug wire. Be sure all moving parts have stopped.

•Lubricate the auger shaft zerk fitting (See the Maintenance section ).

•Align the hole in the auger with the hole

in the auger shaft. Install the new shear bolt and nut found in toolbox located on

top of belt cover.

•Reconnect the spark plug wire.

TO REPLACE:

•If you need a new spark plug, use only the proper replacement spark plug (see page 15).

•Set the gap to .030 inches.

•Before installing the spark plug, coat its threads lightly with oil or grease to insure easy removal.

•Tighten the plug firmly into the engine.

•If a torque wrench is available, torque the plug to 18 to 23 ft. - Ibs.

TO ADJUST CARBURETOR

If you think your carburetor needs adjusting, see your nearest Authorized Craftsman Service Center. Engine performance should not be affected at altitudes up to 7,000 feet. For operation at higher eleva- tions, contact your nearest Craftsman Ser- vice Center.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Snow Thrower Limited TWO-YEAR Warranty on Craftsman Snow Thrower Contents Service and Adjustments 18-22 Warranty StorageTraining Preparation OperationFlatwasher Maintenance and StorageSteep sloping surfaces. do not USE Snow Thrower on Surfaces 8-16 Hex Jam NutsGlasses or eye shields while assembling snow thrower Tools Required for AssemblySpeed Lever HOW to SET UP Your Snow Thrower To Installthe Upper Handle and CrankassemblyReplace carriage bolt AssembleSpeed Selector ROD Remote Chute Control Knob HeadlightKnow Your Snow Thrower Chute Chute Deflector DeflectorTo Move Forward Backward Howto Useyour Snow ThrowerTo Control Snow Discharge To Stopyour SnowthrowerBefore Starting the Engine To Throw SnowTo USE Wheel Lockout PIN Checkthe OILFill GAS Cold StartTo Start Engine Recoil Starter Warm StartPush down on the starter button until Be sure the auger drive and traction driveGages. Then continue with the directions for cold start Frozen Recoil StarterSnow Throwing Tips For maximum snow thrower efficiencyCustomer Responsibilities Service Schedule Dates Records Lubrication ChartSnow Thrower After First USE Lubrication Every 10 HoursLubrication Before Storage After Each USEEngine Lubrication LubricationOIL Recommendation Spark PlugTo Adjust Scraper BAR To Adjust Skid HeightTo Adjustthe Clutch Control Cables Auger Drive Belt To Adjust BeltsTo Replace Belts Traction Drive BeltTo Adjustthe Belt Guide To Adjust the Friction WheelEnd nuts To Replace Friction WheelAuger Replace bottom panelTo Adjust To Adjust or Replace Spark PlugTo Adjust Carburetor To Replace Auger Shear BoltOther Snow Thrower StorageEngine Storage Steps belowTrouble Cause Correction

536.88123 specifications

The Craftsman 536.88123 is a powerful and versatile snow blower designed to tackle the toughest winter weather conditions. With its robust construction and advanced features, this machine is engineered for homeowners who desire efficiency and reliability in snow removal.

One of the standout features of the Craftsman 536.88123 is its impressive 27-inch clearing width. This wide path allows users to cover large areas quickly, making it suitable for both residential driveways and sidewalks. The snow blower is equipped with a strong and efficient 2-stage auger system that not only breaks up compact snow but also throws it far away from the cleared area. This ensures that snow is efficiently removed without simply pushing it aside, which can cause buildup over time.

Another significant characteristic of this model is its powerful 357cc engine, delivering substantial torque and performance. This engine is designed to handle heavy, wet snow with ease, providing users with the confidence to tackle even the most challenging conditions. The electric start feature adds convenience for those cold, winter mornings, allowing for easy ignition without the need for strenuous pulling.

The Craftsman 536.88123 is also designed for user comfort and ease of operation. The adjustable handle ensures a comfortable grip, and it can be modified to fit the user’s height. This snow blower features six forward and two reverse speeds, giving users full control over their snow clearing experience. The durable, rubber-edged auger not only provides efficient snow removal but also protects surfaces underneath, minimizing the risk of damage.

Additionally, the snow blower comes with a remote chute control system, allowing users to easily direct the snow discharge without having to manually adjust the chute. This feature is particularly beneficial for users who need to navigate around obstacles while working.

In terms of durability, the Craftsman 536.88123 is built with high-quality materials designed to withstand harsh conditions, ensuring longevity and dependable performance year after year.

With its combination of power, efficiency, and user-friendly design, the Craftsman 536.88123 is a top choice for those looking for a reliable solution to winter snow challenges. Whether you're clearing your driveway, sidewalk, or patio, this snow blower promises to make your winter maintenance tasks manageable and less labor-intensive.
Top Page Image Contents